高线车间计_成型毕业论文.docVIP

新建年产71万吨告诉线材车间 钢铁是现在社会经济建设的重要资源，而线材又是其中的重要组成部分。 本设计旨在建立一个年产71万吨的高产热轧线材车间。产品规格范围：Φ6～Φ1mm线材，以常见的低碳钢为主展开介绍，简要介绍线材的生产规划流程过程：产品的规格、坯料的选择、加热炉的选择、轧机轧辊的选择与校核、冷却方式的选择等等。 本设计采用了连铸坯，可以减少金属的切损，又因连铸坯的组织结构较好，提高了产品的质量；同时通过采用连铸坯热装热送工艺，通过降低烧损、能耗和减少轧制间隙时间提高生产率。 本设计以优产高产为原则，主要体现在：加热炉为步进梁式加热炉；进出料采用侧进侧出；轧机采用高速无扭线材轧机；采用控制冷却技术，且轧后通过水冷箱和一套斯太尔摩冷却运输系统。 关键词：线材，轧机，坯料，加热炉 New annual output of 710,000 tons to tell the wire mill Abstract Iron and steel is now the important resources of the construction of social economy, and the wire is an important part of one. This design aims to build an annual output of 710000 tons of high yield of hot rolled wire rod plant. Common low carbon steel mainly introduced in this article, brief introduction of wire rod production planning process: product specifications, material selection, the selection of heating furnace, rolling mill roller selection and check, selection of cooling way and so on. This design uses the continuous casting billet, can reduce the metal cutting loss, and because of the continuous casting blank structure structure better, improve product quality; at the same time, through the use of continuous casting billet hot delivery and hot charging process, by reducing the burning loss, energy consumption and reduce rolling gap time to improve productivity. The design and production of high yield for the principle, mainly reflected in: the heating furnace for walking beam heating furnace; feeding the side inlet side; mill adopts high speed non-twist wire rod mill; controlled cooling technology after rolling, and through the water tank and a set of Stelmor cooling transportation system. Keywords：wire，roll，billet，furnace引 言 1 1.线材的基本状况与高线生产简介 1 2.高速线材轧机生产的工艺特点与产品特点 1 3.本设计中采用的先进技术和设备 1 4.线材轧制的发展方向 2 1产品方案和金属平衡表 3 1.1产品大纲 3 1.2产品质量执行标准及产品交货条件 3 1.2.1执行标准 3 1.2.2交货条件 3 1.3原料 4 1.3.1原料来源和年需求量 4 1.3.2钢坯尺寸和质量要求[5] 4 1.3.3对表面质量和内部质量的要求 4 1.3.4连铸坯的化学成分 5 1.4金属平衡表 5 2设计方案 6 2.1轧机数量的确定 6 2.2轧机布置方案 6 3工艺流程 8 3.1工艺流程图 8 3.2生产工艺流程简述 9 3.2.1坯料的选择及加