南天pr打印机的手册及基本操作（Manual and basic operation of Nantian PR printer）.docVIP

下载本文档

33
0
约9.39千字
约 13页
2018-06-17 发布于江西
举报
版权申诉

南天pr打印机的手册及基本操作（Manual and basic operation of Nantian PR printer）.doc

1、本文档共13页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

南天pr打印机的手册及基本操作（Manual and basic operation of Nantian PR printer）.doc

南天pr2打印机的手册及基本操作（Manual and basic operation of Nantian PR2 printer） Basic manual operation of Nantian PR2 printer Basic manual operation of Nantian PR2 printer L print self check (every repair of a printer, must do this operation) 1. turn off the power 2. press and hold the Station2 key on the operating panel, and then open the power until the printer initialization action is completed 3. insert a A4 sized paper into the middle of the feeder slot, when the printer automatically aligns the paper to the correct printing position 4. and then print out a test configuration table L parameter setting 1. turn off the power 2. hold down the Station1 and Station2 keys on the operating panel at the same time, then turn on the power until the printer initialization action is completed 3. insert a A4 specification paper into the feeder 4. printers begin to suck paper and print out two lines of prompt information 5. press the Local button once, and the printer enters the setup state 6. if you press the Station1 key, accept and save the parameters; if you press the Station2 key, change the parameters until the parameters that need to be changed or set are finished 7. parameter change is completed, press the Local key, then press the Station1 button once heard the printer send out two clear call after shutdown. (this parameter change good saved) Refresh of L monitor program Connect the printer with the COM1 port of the host; Open the top cover of the printer, press the [STATION1] and [LOCAL] keys to start, cover the top cover; Run FLASHPR2 VXXX.PR2 on the host; The printer will be downloaded by 8 modules. After downloading, it will check itself once; Before resetting, the factory parameters need to be restored and then set The connection between L printer and host computer Host (9 hole) printer (25 pin) 2-----------------------------------------------------------2 3-----------------------------------------------------------3 5-------------------------------------------------------