毕业设计（论文）-轴支架加工工艺分析与扩三孔夹具设计（全套图纸）.docVIP

课程设计（设计）轴支架加工工艺分析与钻扩三孔夹具设计学 院： 专 业： 班 级： 学生姓名： 指导老师： 完成日期： 摘要轴支架零件加工工艺及夹具设计是包括零件加工的工艺设计、工序设计以及专用夹具的设计三部分。在工艺设计中要首先对零件进行分析，了解零件的工艺再设计出毛坯的结构，并选择好零件的加工基准，设计出零件的工艺路线；接着对零件各个工步的工序进行尺寸计算，关键是决定出各个工序的工艺装备及切削用量；然后进行专用夹具的设计，选择设计出夹具的各个组成部件，如定位元件、夹紧元件、引导元件、夹具体与机床的连接部件以及其它部件；计算出夹具定位时产生的定位误差，分析夹具结构的合理性与不足之处，并在以后设计中注意改进。关键词：工艺，定位，切削用量，夹紧全套图纸加153893706 PAGE 37 PAGE 38AbstractThe bolt body parts and milling fixture design process is the design process design, including machining process design and fixture three. In process design should first of all parts for analysis, to understand part of the process to design blank structure, and choose the good parts machining datum, design the process routes of the parts; then the parts of each step in the process to the size calculation, the key is to determine the craft equipment and the cutting dosage of each working procedure design; then the special fixture, the fixture for the various components of the design, such as the connecting part positioning devices, clamping element, a guide element, fixture and machine tools and other components; positioning error calculated by the analysis of fixture, jig structure the rationality and the deficiency, pay attention to improving and will design in.Keywords: process, positioning, cutting dosage, clamping,目 录 TOC \o 1-3 \u 第1 章 绪论 PAGEREF _Toc432233629 \h 3第2章 零件的分析 PAGEREF _Toc432233630 \h 32.1 零件的作用 PAGEREF _Toc432233631 \h 32.2 零件的工艺分析 PAGEREF _Toc432233632 \h 3第3章 零件的工艺规程 PAGEREF _Toc432233633 \h 43.1 确定毛坯的制造形式 PAGEREF _Toc432233634 \h 43.2 轴支架加工的主要问题和工艺过程设计所应采取的相应措施 PAGEREF _Toc432233635 \h 43.2.1 孔和平面的加工顺序 PAGEREF _Toc432233636 \h 52.2.2 孔系加工方案选择 PAGEREF _Toc432233637 \h 53.3 轴支架加工定位基准的选择 PAGEREF _Toc432233638 \h 63.3.1 粗基准的选择 PAGEREF _Toc432233639 \h 63.3.2 精基准的选择 PAGEREF _Toc432233640 \h 63.4 轴支架加工主要工序安排 PAGEREF _Toc432233641 \h 63.5 毛坯尺寸的确定 PAGEREF _Toc432233642 \h