机械毕业设计(论文)-高线1720卡断剪设计【全套图纸】.docVIP

PAGE 内蒙古科技大学本科生毕业设计说明书题 目：高线1720卡断剪设计 学生姓名：学 号：2003041303专 业：机械设计制造及其自动化班 级：机械2003-3班指导教师：摘 要本设计说明是针对高线1720卡断剪的设计说明。此设备安装在拉出辊之后，1号粗轧机前, 是为在发生堆钢事故时避免影响生产和减少损失而设置。剪切时气动系统使剪刃回转并压向轧件，随后靠轧件的前进带动剪刃继续回转，并逐渐切入轧件中，直至轧件被切断，并将剩下的轧件挡在外面。本次设计完成的内容是：力能参数计算；杆件长度的优化；气动系统的设计；整个机构工作时的受力分析；各主要零件部件的设计校核和设备的润滑关键词：卡断剪；钢坯；气动系统。全套图纸，加153893706 Abstract This paper is a design for 1720 Cranks Flying Shears. This facility is to avoid when occurring Pile steel accident that influence producing and is installed before the NO:1 Rolling mill. This facility’s working is using Pneumatic system and make the cut edge turn around and press to rolled piece, soon afterwards lean rolled piece go forward to drive the cut edge turn around continuously, and gradually cut the rolled piece, till rolled piece had been cut been cut of, and block the rolled piece that leaves in surface.The content of this design completion is: Calculating the mechanics parameter; Optimizing the pole’s length; It is pneumatic and systematic to design; Entire organization work get force analysis; Design each major component.Keyword: Flying Shears; Billet; Pneumatic system.目 录 TOC \o 1-3 \h \z \u HYPERLINK \l _Toc138643774 摘 要 PAGEREF _Toc138643774 \h I HYPERLINK \l _Toc138643775 Abstract PAGEREF _Toc138643775 \h II HYPERLINK \l _Toc138643776 第一章 绪论 PAGEREF _Toc138643776 \h 1 HYPERLINK \l _Toc138643777 1.1 线材生产 PAGEREF _Toc138643777 \h 1 HYPERLINK \l _Toc138643778 1.2 线材生产工艺 PAGEREF _Toc138643778 \h 2 HYPERLINK \l _Toc138643779 1.3 飞剪机介绍 PAGEREF _Toc138643779 \h 4 HYPERLINK \l _Toc138643780 1.4 卡断剪设计特点 PAGEREF _Toc138643780 \h 6 HYPERLINK \l _Toc138643781 第二章 机械结构的设计 PAGEREF _Toc138643781 \h 7 HYPERLINK \l _Toc138643782 2.1 机构的设计 PAGEREF _Toc138643782 \h 8 HYPERLINK \l _Toc138643783 2.2 气动系统的设计特点 PAGEREF _Toc138643783 \h 8 HYPERLINK \l _Toc138643784 第三章 剪切力能参数的计算 PAGEREF _Toc138643784 \h 10 HYPERLINK \l _Toc138643785 3.1 剪切力的计算 PAGEREF _Toc138643785 \h 10 HYPERLINK \l _Toc138643786 3