原创力文档- 1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
- 2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击 这里二次下载。
- 3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
- 4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
- 5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
- 6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
- 7、VIP文档为合作方或网友上传，每下载1次， 网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
罩壳双直角边弯曲模的设计
目录
一 工艺性分析 ······························································2
1.1工艺性分析 ····························································2
1.1.1零件成形工序图·················································· 2
1.1.2方案选择························································ 2
1.2弯曲件的结构工艺性 ···················································3
1.2.1最小弯曲半径 ····················································3
1.2.2弯曲件的直边高度················································ 3
1.2.3板材弯曲零件的弯曲线与板料的纤维方向的关系 ······················4
1.2.4板材弯曲零件的孔与弯曲线的最小距离 ······························4
1.2.5板材弯曲零件的冲裁件毛刺面与弯曲方向 ····························4
1.3弯曲件回弹值的确定 ···················································4
1.3.1回弹值的计算 ····················································4
1.3.2减少回弹的措施 ··················································4
二 弯曲工艺力的计算 ························································5
2.1弯曲件展开长度的计算 ·················································5
2.2校正弯曲力的计算 ·····················································5
2.3顶件力和压力机的确定 ··················································6
2.3.1顶件力和压料力的计算 ············································6
2.3.2弯曲设备标称压力的选择 ··········································6
三 弯曲模工作部分的设计···················································· 7
3.1凸、凹模的间隙值 ·····················································7
3.2弯曲模工作部分尺寸计算 ···············································7
3.3凸、凹模圆角半径 ······················································9
3.3.1凸模圆角半径·················································· 9
3.3.2凹模圆角半径················································· 9
3.4凹模深度的选取 ·······················································9
3.5凹模高度及壁厚 ·······················································9
四 冲压设备的选择 ··························································10
五 模具的结构件设计······················································· 10
5.1模架 ·································································10
5.2操作方式选择 ····················
文档评论（0）