NandFlash引脚及用示波器看到的波形.DOCVIP

NandFlash烧录问题待解决 样板没有烧程序，在上电后用示波器看NandFlash的控制输入脚，看到的波形如下： 7脚 R/B# ：高电平3.3V 19脚WP#：0V 16脚 CLE :0V 8 脚 RE# 9脚：CE# 17脚ALE的波形 18脚：WE#的波形 各信号引脚及封装的说明：（连接的电路图在本文档附录中） 下面是我用Flash V1.6.0.0的烧录过程：烧录下载都没出错，可惜从串口出来的是40x,xload引导界面并没有出来，我也再次用示波器看了一下输入脚的波形，请专家帮我分析分析，是哪出了问题。下面是我所做的过程。 软件：Flash v1.6.0.0 NandFlash：MT29F2G16，大小256M，16位，如下图所示： 配制文件：configuration_am35xxevm_micron_2g.txt 修改的部分如下：（整个文档在最后的附件中） memory NAND1BITBOOT driver Targets\Flash-Drivers\nand_onfi_16bit_8bit.bin parameters gpmc 0x6E000000 cs 0 address 0bberase 0 onfi 0 bpp 1024 sbpp 32 ppb 64 bpl 1024 l 2 acv 0x23 f 0x0019 eccoffset 2 memory NANDINFO1BITBOOT driver Targets\Flash-Drivers\nand_onfi_16bit_8bit.bin parameters gpmc 0x6E000000 cs 0 address 0bberase 0 onfi 0 bpp 1024 sbpp 32 ppb 64 bpl 1024 l 2 acv 0x23 f 0x0019 eccoffset 2 擦除过程：能擦除成功 下面是擦除过程中output输出来的信息 -stdout -omap 3 -no_force_package_alignment -com 1 -t 60 -p EVM_MDDR_MICRON_2G_EMIF -2 chip_erase NANDINFO1BITBOOT 800000 Leaving parameter file:temp_script.txt @temp_script.txt Looking for device (omap com1) Please turn off device, then turn it on again Awaiting ASIC id AsicId items 04 AsicId id 01 05 01 34 30 07 58 AsicId secure_mode 13 02 01 00 AsicId public_id 12 15 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 AsicId root_key_hash 14 15 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Searching 2nd for: EVM_MDDR_MICRON_2G_EMIF 343007 58 GP Loading second file Targets\2nd-Downloaders\dnld_startup_omap3_gp_2g.2nd Entering parameter file:omapflash2nd.txt at line: 15 -pheriphalboot_reopen Reading board configuration file Targets\Configurations\configuration_am35xxevm_micron_2g.txt Reading definition file .\targets\definitions\definitions_omap3.txt -board_config Targets\Configurations\configuration_am35xxevm_micron_2g.txt Leaving parameter file:omapflash2nd.txt Sending size of second file (0bytes) Transferring second file to target (0x6804 bytes) Closing boot connection Found device (om