轴端盖罩冷冲压工艺及模具毕业设计论文机械cad图纸5mbuqwof.docVIP

2013年机械设计专业本科毕业设计（论文） 优秀毕业设计（论文） 通过答辩 摘 要 冲压生产是一种先进的金属加工方法。它是利用模具和冲压设备对板材金属进行加工，通过冲压生产可以获得所属要的零件形状和尺寸。本课题是轴端盖罩零件的冲压模具的设计，本产品外形是圆形，根据设计零件的尺寸、材料、生产批量等要求，分析零件的工艺性，根据工件的形状和批量，对模寿命有一定要求，故采用有废料排样方法，确定冲裁工艺路线方案，从而设计一套复合模具，本次模具选取的是简单的二次拉深工艺模，综合考虑冲压件的形状特点、尺寸大小、精度要求及冲压设备与制模条件，操作方便与安全。模具1：落料拉深复合模和模具2：第2次拉深模，第一副模具是落料拉深复合模，卸料采用弹性（弹簧）卸料结构，工件采用推件块刚性推出，推出机构装在上模部份，压边装置装在下模部份，采用弹性（弹簧）结构，同时也起向上推件作用。条料采用手动送料装置，样时工件之间以及工件与条料侧边之间留下的余料叫做搭边。搭边的作用是补偿定位误差，保证冲出合格的工件。还可以使条料有一定的刚度，便于送进。由于第一副模具是落料拉深复合模，只需考虑落料的排样，故采用单排直排方式。 采用单排直排方式在保证工件的尺寸和形状位置精度要求的同时，尽量的提高材料的利用率和生产效率。随着计算机技术的不断发展，采用CAD/CAE/CAM一体化技术可以准确、快速的完成模具设计制造。本文主要是介绍说明了轴端盖罩零件成形的各个工序及其模具的设计及尺寸计算，在结构设计的同时，对主要零件的设计和装配要求技术进行了分析。设计时考虑到模具设计合理、简单，便于制造和修模，有利于缩短模具生产制造周期，降低成本。 　　关键词：盖罩零件；冲压工艺；复合模；模具设计 Abstract Stamping production is a kind of advanced metal processing method. It is the use of mould and stamping equipment to carry on the processing of sheet metal. Through stamping production, we can get the shape and size of the parts which we need. This topic is about the design of the stamping mould for the shaft end cover parts. According to requirements of part size, material, production batch, etc. we should analyze the manufacturability of parts, and determine a medium manufacture route to design a set of compound mould. The mould selection of deep drawing technology is a simple quadratic model, considering the shape of the stamping characteristics, size, accuracy and stamping equipment and molding conditions, convenient operation and safety. Mold 1: blanking deep drawing die and mould 2: the second drawing die, first deputy die blanking, deep drawing composite modulus is discharging structure of elastic unloading (spring), artifacts using push a piece of rigid, launch mechanism mounted on the upper die, blank holder device installed in mold parts, the structure of elastic (spring), and push up a role as well. Manual feeding device for the strip material, article sample between artifacts and artifact and between the material side of excess sto