【毕业论文】北方某市污废水处理工程设计论文.doc

PAGE \* MERGEFORMATI l 目 录 TOC \o 1-1 \h \z \u HYPERLINK \l _Toc356241520 摘 要 PAGEREF _Toc356241520 \h I HYPERLINK \l _Toc356241521 ABSTRCT PAGEREF _Toc356241521 \h II HYPERLINK \l _Toc356241522 第一卷 第一册 设计说明书 PAGEREF _Toc356241522 \h 1 HYPERLINK \l _Toc356241523 第二卷 第二册 工程概算书 PAGEREF _Toc356241523 \h 50 HYPERLINK \l _Toc356241524 第三卷 第三册 图纸目录 PAGEREF _Toc356241524 \h 56 HYPERLINK \l _Toc356241525 参考文献 PAGEREF _Toc356241525 \h 58 HYPERLINK \l _Toc356241526 致 谢 PAGEREF _Toc356241526 \h 59 HYPERLINK \l _Toc356241527 附录 1 外文参考文献（译文） PAGEREF _Toc356241527 \h 60 HYPERLINK \l _Toc356241528 附录 2 外文参考文献（原文） PAGEREF _Toc356241528 \h 65 北方某市污废水处理工程 摘 要 本设计为北方某市污废水处理厂的初步设计，要求污水处理厂出水按《城镇污水处理厂污染物排放标准》（GB18918-2002）的一级B标准排放。由于污水来源主要为生活污水，氮磷含量较高，由此设计中需要考虑到脱氮除磷。该厂二级生物处理主要采用A2/O处理工艺，主要构筑物为：泵前中格栅、提升泵房、细格栅、旋流沉砂池、平流式沉淀池、A2/O反应池、辐流式沉淀池、紫外线消毒渠。污泥处理构筑物有：重力浓缩池、污泥脱水机房等。 污水厂设计方案为： 污水处理流程：粗格栅 → 污水提升泵房 → 细格栅 → 旋流沉砂池 →A2/O反应池→ 消毒接触池→ 排放； 污泥处理流程：剩余污泥 → 浓缩池 → 贮泥池→ 污泥脱水机房 → 泥饼外运。 关键词：污泥处理，A2/O工艺，脱氮除磷， ABSTRCT The design for the preliminary design of the north city wastewater treatment plant effluent from a sewage treatment plant, requirements according to the urban sewage treatment plant pollutant discharge standard (GB18918-2002) of a standard B emission. Because the sewage originates is mainly the sanitary sewage, the nitrogen phosphorus content is high, from this designs needs to consider the denitrogenation eliminates the phosphorus. This factory second-level biological treatment mainly uses a2/O processing craft, the main construction is: Before the pump, the grill, promotes the pump house, the thin grill, the eddy sand collector, the advection type sedimentation pond, a2/O response pond, the spoke class type sedimentation pond, the ultraviolet ray disinfection ditch. The sludge treatment construction includes: Gravity concentration basin, sludge dewatering engine room and so on. The process of the wastewater plant that the wasterwater treatment plant adopted