- 1、本文档共53页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
摘要
PAGE IV
5T双梁桥式起重机小车起升机构设计
摘 要
此次课题设计来源是依据卫华集团起重机厂的工作实际,课题性质属于实际工程设计。
此次设计是5T双梁桥式起重机小车起升机构的设计。首先通过大量的阅读桥式起重机有关专刊和文献,大致总结出国内外双梁桥式起重机的发展趋势以及双梁桥式起重机的特点与分类,并仔细分析了双梁桥式起重机的组成及其工作原理。根据课题设计参数及设计要求制定出双梁桥式起重机小车起升机构的总体设计方案和一些主要零部件的初步选择;其次在小车起升机构的计算中,确定了小车起升机构的传动方案,并进行了钢丝绳和吊钩组的设计与计算以及滑轮组和卷筒的设计与计算,验算了起升静功率。通过对电动机及减速器的设计与计算,进行了电动机的过载验算和发热验算。又根据制动器及联轴器的设计与计算,验算了起动时间和制动时间,并进行了高速轴的疲劳计算和静强度计算;最后在小车及起升机构的机构设计里,分析了小车及起升机构的结构组成,重点完成了卷筒组的机构设计,并完成电气控制系统的设计。通过一系列的设计,满足了起重量5t和起升高度为16m 的课题设计要求。
关键词:起重机,桥式,起升机构,小车,卷筒组
5-TON DOUBLE BEAM BRIDGE CRANE HOISTING MECHANISM DESIGN CAR
ABSTRACT
This topic design source is the basis of tissue plasminogen activator group crane factory working practice, belong to actual engineering design issues.
This design is 5-ton double beam bridge crane car hoisting mechanism design. First through extensive reading bridge crane special and documents, roughly about summarized the domestic and foreign double beam bridge crane development trend and the characteristics of double beam bridge crane, and careful analysis and classification of the double beam bridge crane composition and working principle. According to the study design parameters and design requirements formulate double beam bridge crane car of hoisting mechanism overall design scheme and some of the main parts of the preliminary selection; Second in the calculation of hoisting mechanism in the car, determine the transmission scheme hoisting mechanism, and the wire rope and hook group design and calculation and pulleys and drum design and calculation, the checking the hoisting static power. Based on the electric motor and reducer, the design and calculation of the electric motor and feer checking computations overload. And according to brake and coupling calculating design and calculation of the start time and braking time, and a high-speed shaft fatigue calculation and static strength calculation; Finally in the car and hoisting mechanism, analyzes the mechanism design in the car and hoisting mechani
您可能关注的文档
- 《(AIO)品牌行业前景调查及投资策略分析报告》-毕业论文.docx
- 《(冷冲压)山字形芯片跳步模具设计说明书》-毕业论文.doc
- 《(设计)-基于PLC的自动浸锡机的课程设计》-毕业论文.docx
- 《(终稿)虚拟硬盘启动计算机技术的分析及改进-王成-》-毕业论文.doc
- 《“CA6140”拨叉工艺工装及铣8槽夹具设计》-毕业论文.doc
- 《“Y”形支架双面钻机床总体设计和左主轴箱设计》-毕业论文.doc
- 《“Y”形支架双面钻机床总体设计及前主轴箱设计》-毕业论文.doc
- 《“Z”型导电片冲压模具设计》-毕业论文.doc
- 《“基于AT89C51单片机综合火灾报警器”生产工艺_实习报告》-毕业论文.doc
- 《“三通圆形塑料接线盒”注射成型模具设计》-毕业论文.doc
文档评论(0)