《刀具刃磨中心车刀夹持模块设计与建模》-毕业论文.docVIP

w 刀具刃磨中心车刀夹持模块设计与建模 [摘要] 本文主要阐述了车刀等常用刀具的种类及其分类方法；建立了常用车刀的三维零件模型；并确定了车刀刃磨的参数；对车刀角度及车刀角度对切削加工的影响作了研究和分析；详细阐述了刀具各个角度的刃磨方法；研究车刀不同位姿，建立其数学模型并设计相应夹具。 [关键词]车刀角度 刃磨参数 三维建模 数学模型 刃磨装置 Knives cutting tool clamping module design center with modeling Qin Shan (Grade07,Class4,Major Mechanical design and manufacture of extremely automation ，Mechanical Engineering College Dept.，Shaanxi University of Technology，Hanzhong 723003，Shaanxi ) Tutor：Zhang Junfeng Abstract：This paper mainly expounds the commonly used tools such as tool type and classification method; Established three-dimensional parts model cutting tool; The cutting tool to determine the parameters; On turning Angle and turning Angle to cutting the influence of the research and analysis; Explains in detail the method of each Angle cutting tools; Research tool, establish its position and pose different mathematical model and design corresponding fixture. Key words：Lathe tool Turning Angle Gear parameters Three dimensional modeling Mathematical model Fixture design w 目 录 TOC \o 1-3 \h \u HYPERLINK \l _Toc2925 引 言 PAGEREF _Toc2925 1 HYPERLINK \l _Toc6583 1. 车刀刃磨参数分析 PAGEREF _Toc6583 2 HYPERLINK \l _Toc7514 1.1车刀基础知识 PAGEREF _Toc7514 2 HYPERLINK \l _Toc13150 1.1.1 车刀的组成 PAGEREF _Toc13150 2 HYPERLINK \l _Toc4085 1.1.2 车刀的角度和主要作用 PAGEREF _Toc4085 2 HYPERLINK \l _Toc13078 1.2常用车刀的种类和用途 PAGEREF _Toc13078 3 HYPERLINK \l _Toc29451 1.2.1普通车刀的结构分类 PAGEREF _Toc29451 3 HYPERLINK \l _Toc18642 1.3 车刀各个角度对切削的影响 PAGEREF _Toc18642 5 HYPERLINK \l _Toc4474 1.3.1前角的功用及选择 PAGEREF _Toc4474 5 HYPERLINK \l _Toc30905 1.3.2 后角功用及选择 PAGEREF _Toc30905 6 HYPERLINK \l _Toc25035 1.3.3 主偏角的功用及选择 PAGEREF _Toc25035 7 HYPERLINK \l _Toc25304 1.3.4 副偏角的功用及选择 PAGEREF _Toc25304 8 HYPERLINK \l _Toc8402 1.3.5 刃倾角的功用及选择 PAGEREF _Toc8402 8 HYPERLINK \l _Toc432 1.4不同车刀在不同切削条件下的刃磨参数 PAGEREF _Toc432 9 HYPERLINK \l _Toc13351 1.4.1外圆车刀几何参数的参考值 PAGEREF _Toc13351 9 HYPERLINK \l _Toc27970 1.4.2常用切断刀的几何参数 PAGEREF _Toc27970 11