网站大量收购闲置独家精品文档,联系QQ:2885784924

放电等离子烧结石墨烯增韧氧化锆陶瓷基复合材料力学性能研究-机械工程专业论文.docx

放电等离子烧结石墨烯增韧氧化锆陶瓷基复合材料力学性能研究-机械工程专业论文.docx

  1. 1、本文档共79页,可阅读全部内容。
  2. 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
  3. 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载
  4. 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
放电等离子烧结石墨烯增韧氧化锆陶瓷基复合材料力学性能研究-机械工程专业论文

PAGE PAGE IV 放电等离子烧结石墨烯增韧氧化锆陶瓷基复合材料力学性能研究 5.6MPa m0.5).。 研究发现 GNS/TZP 复合材料主要增韧机制是石墨烯的拔出,桥接, 裂纹的偏转和裂纹的分叉。采用已有模型计算了复合材料界面在应力,并得出了 GNS 的临界增韧长度。计算了 GNS 的拔出应力释放率和复合材料的残余热应力,结果表 明残余热应力对于复合材料的力学性能影响可以忽略。仪器化划入测试结果表明,尽 管 GNS/TZP 复合材料的摩擦系数高于 TZP,但纯 TZP 材料在仪器化划入过程中的 损伤机制主要表现为脆性断裂,而 GNS/TZP 复合材料则转变为粘着磨损为主、脆性 断裂为辅的损伤机制,这主要源于 GNS/TZP 复合材料断裂韧性的显著改善。 关键词:石墨烯;氧化锆;力学性能;增韧。 作 者: 苏佳楠 指导老师: 陈 瑶 The mechanical properties of graphene nanoplatelets reinforced zirconia composite The mechanical properties of graphene nanoplatelets reinforced zirconia composite Abstract Zirconia ceramic material possesses very excellent chemical and physical properties. It has good physical and mechanical properties at room temperature, and also because of its high temperature resistance, good chemical resistance, it usually served in harsh environments and load conditions, so it is a very promising high-temperature ceramics. However, its intrinsic brittleness of ceramic and poor tribological properties, greatly limit it’s the wider applications. To achieve high mechanical performances, much effort has been devoted to develop zirconia ceramic-based composites , in whch ZrO2 matrix is toughened with high strength fibers, whiskers, hard particles and carbon nanotubes (CNTs). Graphene nanosheets (GNSs) are composed of a few graphene layers held together through weak van der Waals force, and they display compatible properties similar to that of monolayer graphene (e.g. tensile strength 130 GPa and Young’s modulus 0.5-1 TPa) , and GNSs are expected to be used as nanofillers in ceramics to produce composites with improved fracture toughness. Therefore, fabrication of the GNS reinforced 5 mol.% yttria stabilized tetragonal zirconia polycrystals (TZP) composites using spark plasma spray sintering (SPS) was proposed in this research, and the microstructure characteristics and the mechanical properties such as elastic modulus, hardness and fracture toughness of sintered composites were analyzed. Ultrasonic dis

文档评论(0)

peili2018 + 关注
实名认证
内容提供者

该用户很懒,什么也没介绍

1亿VIP精品文档

相关文档