原创力文档- 1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
- 2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击 这里二次下载。
- 3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
- 4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
- 5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
- 6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
- 7、VIP文档为合作方或网友上传，每下载1次， 网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
PAGE
PAGE 21
金属材料工程
课程设计说明书
设计题目： 机用连杆螺栓
专 业 材料科学与工程
班 级
学 生
指导教师
2013 年 秋季 学期
设计任务
本次设计机用连杆螺栓，圆柱部位为φ13mm，长度为70mm。技术指标要求：σs≥800MPa，δ≥10%，ψ≥42%，ak≥6-7Kg/C㎡,HRC30-35。请选用合理的材料和适宜的热处理工艺达到此技术指标。
摘要
本次课程设计是运用有关手册、规范、图表等技术资料，选择高效、省力、经济合理而能保证所要求的零件质量、技术指标的工艺方案，对机用连杆螺栓工件的服役条件、材料的选取、零件加工工艺路线、热处理工艺、性能检测方法及分析的设计说明。其中最主要的是对机用连杆螺栓的合理选材以及热处理工艺的规范设计和说明。
目录
一、概述·················??·························································1
1.1定义·········································································1
1.2连杆螺栓作用·······························································1
二、工件服役条件······························································2
2.1连杆螺栓零件图····························································2
2.2连杆螺栓受载情况·························································2
三.工件材料选取······························································3
3.1工件材料选取分析·························································3
3.2连杆螺栓紧固件材料选取·················································4
四、零件加工工艺路线························································5
五、工件热加工工艺过程·····················································5
5.1连杆螺栓的热处理技术条件···············································5
5.2 预先热处理································································5
5.4最终热处理·································································6
5.5热处理注意事项····························································7
5.6连杆螺栓热处理后常见的质量缺陷·······································8
六、性能检测方法及分析····················································10
6.1力学性能检验·····························································11
6.2成分、组织及微观形貌检验···············································12
七、总结与建议································································12
参考文献·········································································14
一、概述
1.1定义
螺栓：由头部和 HYPERLINK /view/244927.htm \t _blank 螺杆（带有外螺纹的圆柱体）两部分组成的一类紧
文档评论（0）