塑料模具探头课程设计.docVIP

下载本文档

4
0
约2.23万字
约 32页
2019-04-17 发布于江西
举报
版权申诉

塑料模具探头课程设计.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

PAGE PAGE 26 《塑料成型模具设计》课程设计设计说明书探头注塑成型工艺及模具设计起止日期： 2011 年 12 月 12 日至 2011 年 12 月 23 日学生姓名李浩然班级材料成型083班学号 08405300313 成绩指导教师(签字) 机械工程学院 2011年 12 目录第1章塑料成型工艺性分析········································································ 4 1.1 塑件分析································································································ 4 1.2 性能分析································································································ 4 第 2 章分型面位置的分析和确定····························································· 5 2.1分型面的选择原则·················································································· 5 2.2分型面选择方案······················································································ 6 第 3 章塑件型腔数量及排列方式的确定················································ 7 3.1 数量····································································································· 7 3.2 排列方式······························································································ 8 第 4 章注射机的选择和有关工艺参数的校核········································ 9 4.1 所需注射量的计算················································································ 9 4.2 塑件和流道凝料在分型面上的投影面积及所需锁模力的计算·············· 11 4.3 注射机型号的选定················································································ 11 4.4 有关工艺参数的校核············································································ 12 第5章浇注系统的形式选择和截面尺寸的计算······································ 13 5.1主流道的设计·························································································· 13 5.2分流道的设计·························································································· 14 5.3浇口的设计······························································································ 16 5.4分流道设计······························································································ 17 5.5浇注系统的平衡·······················································