给水管网课程设计说明书.docxVIP

PAGE PAGE 2 给水管网课程设计说明书 姓名：xxx 班级：xxxxxx 学号：xxxxxxxx 专业：给水排水工程 目 录 Ⅰ. 给水管网课程设计任务书·········································3 设计项目·····················································3 设计资料·····················································3 三、设计任务及成果················································ 3 Ⅱ. 给水管网设计计算说明书·········································4 给水管的定线与布置···········································4 设计用水量的计算 ············································4 2.1基础数据···················································4 2.2 最高日设计用水量的计算····································4 2.3最高日最高时设计用水量的计算·······························5 经济管径的确定···············································5 3.1沿线流量及节点流量的计算···································6 3.2泵站设计供水流量的计算·····································6 3.3水塔设计供水流量的计算·····································7 3.4最高时管段沿线流量分配与节点设计流量计算······················7 3.5初始分配流量及管径的确定·········································8 四、管网水力计算···························································8 4.1摩阻系数的确定·····················································9 4.2管网平差··························································10 Ⅲ参考文献·································································12 Ⅳ附录 附录一、城市最高日用水量变化曲线 附录二、管段平差计算表 附录三、给水管网布置图 附录四、水力计算成果图 Ⅰ. 给水管网课程设计任务书 一、设计项目 某市开发区给水管网初步设计 二、设计资料 1、该小城区道路工程规划图一张 2、该街区居民区最高日综合用水量标准 3、 居住区人口密度为 4、工厂甲的集中用水设计流量是（每增加一个学号，该集中用水量增加）； 工厂乙的集中用水设计流量是（每增加一个学号，该集中用水量增加）； 工厂丙的集中用水设计流量是（每增加一个学号，该集中用水量增加）； 城市浇洒道路用水定额采用1.5L/(m2.d)，市政绿化广场用水定额2.0 L 5、时变化系数1.42 （每增加一个学号，该值加0.01） 6、最小服务水压为20m 三、设计任务及成果 1、给水管网设计计算 ① 设计基本数据的选择； ② 给水管的定线与布置以及方案的选择； ③ 给水管道设计计算； 2、设计成果 ① 设计计算书 计算依据：重要的基础数据、有关规范规定，可列在表格内 计算方法：列出主要的计算公式，说明重要的参数的选取依据 计算过程：列出计算步骤 计算结果：列出重要的计算结果 计算书应计算正确，并附有工艺简图，标注所计算的尺寸 ② 绘制给水管道平面布置图和水力计算成果图； Ⅱ. 给水管网设计计算说明书 一、给水管的定线与布置 根据所给资料，结合城镇规划并考虑经济性和供水可靠性的要求，决定了采用环状给水的布置形式，并在管网中布置水塔，水厂至管网采用双管输水。 其中工厂甲和丙有节点5供水，工厂乙由节点4供水，集水管的具体布置形式见附录一。 二、设计用水量的计算 2.1基础数据 1、开发区浇洒道路实际面积N3a：121482.25m2 (由CAD根据比例尺测得,下同 2、市政广场实际面积N3b