安山煤矿开采设计_采矿专业毕业设计.doc

设计题目：安山煤矿42、52煤开采设计 专 业：采矿工程 摘 要 本设计为安山煤矿开采设计。该井田地质条件简单，可采煤层有2层，地质资源储量为145.55Mt，设计可采储量为84.35Mt，设计生产能力1.2Mt/a,服务年限50.2a。 本矿井采用平硐开拓方式，共布置2个开采水平，首采第一水平。设置四个井筒，即主平硐、副平硐、回风斜井及回风平硐。采区划分，条带式开采，采用一次采全高走向长壁综合机械化采煤法，后退式回采。工作面长度200m，工作制为“四六制”，日进9刀煤。主平硐采用胶带输送机运输，副平硐采用无轨胶轮车运输。瓦斯涌出量低，为低瓦斯矿井，采用中央并列式通风系统，抽出式通风。 关键词：安山煤矿 平硐开拓 矿井通风 无轨胶轮车 设计类型：模拟型 Subject：An Shang42、52 coal mine mining design Specialty：Mining Engineering Undergraduate： （Signature） Instructor： （Signature） Abstract This design is done for the An Shan mine.The geological condition of coal mine is simple，there are 2 layers of coal which are recoverable and the retain geological reserves is 145.55Mt and the recoverable reserves of design is 84.35Mt and the designed mine capability is 1.2Mt/a; the mime service life is 50.2 years. This mine use the manner of adit multi-level open up,there are 2 levels be setted and the first mining level is level 1.There are 4 shafts,the main adit,the vice adit ,return air adit and the back to the wind shaft.Mining area divided and strip mining and use of full height once mining Longwall comprehensive mechanized mining method. The face length is 200m as follows the 4-6 work system into 9 cycles each day. The main adit use belt conveyor transport and vice adit use trackless vehicle transport.The mine gas emission is lower, so it is identified gassy mine well.Using breakdown ventilation system and exhaust ventilation. Key words：Anshan coal mine adit to open up Mine ventilation Trackless tire vehicle Design type : simulation model 目录 TOC \o 1-3 \h \u ，长度441m，担负矿井辅助运输任务，并兼进风。 错车段净宽度6.0m，净断面20.7m2，长度20m，每隔150m设1处。 3、一采区回风平硐 净宽度4.5m，净断面13.8m2，倾角6o48′43，长度89m。 后期风井布置 井田可采范围东西约11km，南北约6.5km。根据开拓布置，F2断层以北若与F2断层以南采用同一通风系统，通风线路约单程14.0km，双程约28.0km，其通风阻力超限。设计根据地形及通风线路，在F2断层以北大墩沟布置１个回风立井，以主、副平硐进风，经对最远线路网络解算，总通风阻力4383.5Pa。不符合《煤矿安全规程》、《煤矿井工开采通风技术条件》（AQ1028－2006）规定。在大墩沟风井场地增加1个进风立井，经对最远通风线路网络解算，通风摩擦阻力2192.1Pa，局部阻力219.2Pa，总通风阻力2411.3Pa，符合要求。故设计在大墩沟风井场地设置