ADC0832采集模拟信号控制PWM输出程序（51汇编）.docVIP

ADC0832采集模拟信号控制PWM输出程序（51汇编） 应用电子 2008-06-05 20:46:13 阅读135 评论0 字号：大中小 ?这个程序是通过ADC0832采集模拟信号控制PWM输出，ADC0832只用了通道0一个模拟量通道，PWM采用调节占空比的方式实现。T0实现固定周期，T1实现占空比调节。PWM通过P0.0口输出。;******************************************************;功能：通过ADC0832采集模拟信号控制PWM输出;设计者：蓝若天来源：;晶振频率：12MHz;?利用定时器控制产生占空比可变的?PWM?波???????;*********端口定义*****************?????????B00????EQU??00H?????????D21????EQU??21H????????????????;中断次数存储单元?????????D22????EQU??22H????????????????;A/D转换数据存储单元?????????D23????EQU??23H????????????????;A/D转换数据除以十后存储单元?????????PWM????EQU??24H????????????????;PWM赋初始值?????????D28????EQU??28H?????????PWMOUT?EQU??P0.0???????????????;PWM输出口?????????ADCS?BIT??P3.5??;使能接口?????????ADCLK??BIT??P3.4??;时钟接口?????????ADDO?BIT??P3.3??;数据输出接口?????????ADDI?BIT??P3.2??;数据输入接口;－－－－－－－－－－－－－－－－－－－－－－－－－－－－?????????ORG???0000H?????????AJMP??MAIN?????????ORG???000BH?????????AJMP??INTT0?????????ORG???001BH?????????AJMP??INTT1?????????ORG???0030H;－－－－－－－－－－－－－－－－－－－－－－－－－－－－;主程序;定时器0工作在模式1，定时器1工作在模式0。;－－－－－－－－－－－－－－－－－－－－－－－－－－－－MAIN:??????????MOV?????SP,#70H??????????MOV?????D28,#14H????????????????;装入T0中断次数??????????MOV?????TMOD,#02H??????????MOV?????TH0,#38H????????????????;0.2ms延时常数??????????MOV?????TL0,#38H????????????????;频率调节??????????SETB????EA??????????SETB????ET0??????????SETB????ET1??????????SETB????TR0START:??????????CLR?????B00??????????MOV???B,#02H????;装入通道功能选择数据值（这里选择单端CH0）??????????ACALL???ADC0832??????????ACALL???DEAL??????????MOV?????DPTR,#TAB??????????MOV?????A,D23??????????MOVC????A,@A+DPTR??????????MOV?????PWM,A??????????MOV?????TH1,PWM?????????????????;脉宽调节??????????JNB?????B00,$??????????SJMP????START??????????TAB:??????DB??????00,135,140,145,150,155,160,165,170,175??????????DB??????180,185,190,195,200,205,210,215,220,225??????????DB??????230,235,240,245,250,255;/*-------------------------------------------;子程序名：??ADC0832?子程序;程序功能：???将模拟电压量转换成数字量;实现方法：??串行通信。;植入说明：??占用A、B、CY、R3;----------------------------------