电梯故障代码表OTIS.doc

OTIS XIZI OTIS 21VF/ 故障代码表MCS321/? 故障代码表TOEC2000/??故障代码表300VF?故障代码表 1100??????? SOFTWARE? RESET? 软件复位1101??????? RING SOFTWARE RESET? 群控软件复位 1200??????? SIO MESSAGE FRAMING ERROR? 从MCSS接受到的数据信息中检测到结构错误1201??????? SIO TIMEOUT ERROR? 与MCSS通讯超时1300??????? RSL1 LOSS OF SYNCHRONISATION? 轿厢通讯收发不同步1301? RSL2 LOSS OF SYNCHRONISATION? 厅外通讯收发不同步1302? RSL3 LOSS OF SYNCHRONISATION? 群控通讯收发不同步1400? RSL1 TOTAL PARITY ERRORS? 轿厢通讯出现奇偶校验错误1401? RSL2 TOTAL PARITY ERRORS? 厅外通讯出现奇偶校验错误1402? RSL3 TOTAL PARITY ERRORS? 群控通讯出现奇偶校验错误1500??????? RING1 CHECKSUM ERROR? 群控环1通讯有检测故障1501??????? RING1 TIMEOUT ERROR? 群控环1通讯有超时故障1700??????? MCSS NOT AVAILABLE? MCSS通讯故障1701??????? CAR SHUTDOWN WHILE IN EPO? 备用电源操作时出现故障1702??????? DTC PROTECTION COUNT? DTC关门保护 1703??????? DTO PROTECTION COUNT? DTO关门保护1704??????? DELAY CAR PROTECTION? DCP保护1800? EFO-P AND EFO-CK ARE INVALID OR DO NOT MATCH? 消防楼层参数错误或EFO-P与EFO-CK不一致或该层门被封1801? ASL-P AND ASL-CK ARE INVALID OR DO NOT MATCH? 消防可选楼层参数错误或ASL-P与ASL-CK不一致或该层门被封EFS AND EFS-CK ARE INVALID OR DO NOT MATCH? 消防类型参数错误或EFS与EFS-CK不一致ASL2-P AND ASL2-CK ARE INVALID OR DO NOT MATCH?? 消防第二可选楼层参数错误或ASL2-P与ASL2-CK不一致或该层门被封 1804?? RCBII电池电压不足1805? EQO HOISTWAY SENSOR FAILED? 地震井道传感器故障1806??????? INVALID EQO PARAMETER SETUP? 无效的地震参数1807??????? CAR IS CONFIGURED FOR RANDOM CALLS? 电梯由随机内外呼控制运行 故障代码??????? 服务器显示??????? 说??????????????? 明2000??????? STM software reset??????? 电子板软件运行错误，引起CPU复位。2001??????? STM power on reset??????? 上电复位，或者按了复位按钮。2002??????? STM power fail??????? 5V电源的电压低于2.5V。在系统失电期间，系统停机。2005??????? STM not available??????? 某些非正常状态被MCSS检测到,这时应查其他故障记录.另外,在紧急或检修状态下也有此记录 故障来源：位置参考 故障代码??????? 服务器显示??????? 说???????????????????? 明2100??????? PSR Big pos slip??????? 与电梯运行方向一致的钢丝绳滑移太大。2101??????? PSR Big neg slip??????? 与电梯运行方向相反的钢丝绳滑移太大。2102??????? PSR Pos mes flt??????? PVT读取的位置已位于平层区,但DZ未有输入,应检查光电.2103??????? PSR Inv FLOOR COUNT??????? 无效的楼层计数，楼层计数与实际井道楼层数不一致，或者超出最高或最低楼层的限制。一般发生于断电后轿厢位置被移动,再次送电后即有此故障 2106??????? PSR DZ1 err