HYPCK 多波束安装校准.pptVIP

* Nice graphic! Line separation? 1x depth at shallow end as you stated in another slide? 1? x depth?—I thought that’s what Pat said. * Nice graphic! Line separation? 1x depth at shallow end as you stated in another slide? 1? x depth?—I thought that’s what Pat said. * Nice graphic! Line separation? 1x depth at shallow end as you stated in another slide? 1? x depth?—I thought that’s what Pat said. * Added GPS latency also to HYPACK? Hardware. * Added GPS latency also to HYPACK? Hardware. * Added GPS latency also to HYPACK? Hardware. * Added GPS latency also to HYPACK? Hardware. * “Decent” sounds subjective…maybe “clear” , “clean” or “distinct”? * “Decent” sounds subjective…maybe “clear” , “clean” or “distinct”? HYPACK? 2011 Training Seminar HYPACK? 2011 Training Seminar HYPACK? 2011 Training Seminar HYPACK? 2011 Training Seminar HYPACK? 2011 Training Seminar HYPACK? 2011 Training Seminar HYPACK? 2011 Training Seminar HYPACK? 2011 Training Seminar HYPACK? 2011 Training Seminar HYPACK? 2011 Training Seminar HYPACK? 2011 Training Seminar HYPACK? 2011 Training Seminar HYPACK? 2011 Training Seminar 多波束安装校准 HYSWEEP? 多波束校准 进行单探头或双探头多波束校准. 也可以进行激光扫描仪安装校准. 多波束安装校准 右图是探头横摇安装出现误差时，跑往返线时对数据造成的影响。 多波束校准可以确定下面的参数: 多波束探头安装的横摇,综摇与朝向偏差。测量的偏差角是从多波束探头到MRU及船朝向的偏差。安装偏差可以导致水深数据的深度值及位置出现偏差。 GPS延迟。延迟可以导致水深数据的位置误差。 USACE Requirements for Patch Testing (EM1110-2-1003) 在多波束系统最初安装后应进行校准，且在每次各设备位置改变，重新安装后要再次校准。 横摇校准： 选择平坦地形. 选择大的起伏地形,沿开挖好的平坦航道即可校准 校准的位置 延迟，纵摇与朝向校准： 选择较大的起伏地形。 开挖的航道边坡可以用来校准。 也可以使用水下布放的管线位置校准。 有时可以在符合上述所有要求的同一个区域完成校准。 所有的校准都可以在上图中完成，图中既有平坦地形，也有起伏地形。 单探头布线方式： 横摇校准: 选择线A-B，平坦地形，按照正常测量航速跑往返线 纵摇校准: 选择线C-D，起伏地形，按照正常测量航速跑往返线。 朝向校准: 线C-D与线E-F，起伏地形，按照正常测量航速同向跑平行线，两线之间有50% 数据重叠。 延迟校准: 线C-D， 起伏地形，按照高低两种船速同向跑同一根线。 D C F E B A 双探头布线方式（本系统不适用） Overlap: Green = Port Head. Red = Starboard Head. Roll and Pitch Test Different line geometry to overlap port and starboard heads separately. Requires 3 survey lines instead of 2. Lines A and B overlap starboard head. Lines B and