电源技术应用概述.pptVIP

* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * Audited by Professor Lee Made by Fransiskus * Audited by Professor Lee Made by Fransiskus * Audited by Professor Lee Made by Fransiskus * Audited by Professor Lee Made by Fransiskus * Audited by Professor Lee Made by Fransiskus * Forward Converter With Improved Reset Circuitry Third Generation Audited by Professor Lee Made by Fransiskus * Audited by Professor Lee Made by Fransiskus * Audited by Professor Lee Made by Fransiskus * Audited by Professor Lee Made by Fransiskus * Audited by Professor Lee Made by Fransiskus * Audited by Professor Lee Made by Fransiskus * Audited by Professor Lee Made by Fransiskus * Audited by Professor Lee Made by Fransiskus * Audited by Professor Lee Made by Fransiskus * Audited by Professor Lee Made by Fransiskus * 正向变换器 常用的复位方法 复位绕组 优点 重复利用磁能 缺点 最大负载循环低于50% 变压器设计及成本 电阻电容二极管缓冲器 优点 结构简单，成本低廉 最大负载循环可能高于50% 缺点 功耗高，效率低 Audited by Professor Lee Made by Fransiskus * 正向变换器 有源钳位方法 Vout 优点 重复利用磁能 Q1 和 Q2 是软开关 对称驱动变压器 工作负载循环高于50% Q1, Q2, Da, Db承受的电压应力低 波形平滑；电磁干扰低 缺点 电路复杂 额外的导通损耗 (更高的IM) ZVS! NO ZVS! Audited by Professor Lee Made by Fransiskus * 有源钳位方法 在ATX开关电源正向变换器中的优点 重复利用磁能, Q1 和 Q2 零压开关导通 高效高频工作（效率大于80% ）；变压器和输出扼流圈的尺寸小， 可以使用无功耗的关断缓冲器：进一步提高效率 变压器充分利用铁氧体的能量积（BH）特性 DB 可以提高，变压器尺寸减小 工作负载循环大于50% 调节范围扩大：用一个小型体电容可以保持输出电压 Q1, Q2, Da, Db承受的电压应力低 低额定电压器件(Q1 和 Q2采用600V器件): 更低成本和/或更高效率 平滑波形和软开关 电磁干扰降低：更易于滤波 180° 反相栅驱动信号 易于执行输出同步整流 Audited by Professor Lee Made by Fransiskus * 有源钳位 一个300W正向变换器的性能 % RCD钳位 有零压开关的有源钳位 无零压开关的有源钳位 RCD Active w/o ZVS Active w/ ZVS % CH2: 钳位电容器电流 CH1: 钳位电容器电压 对应变压器不同的气隙值的漏极电压 RCD钳位 有零压开关的有源钳位 无零压开关的有源钳位 立即导通 * * * * * * * * * * * * * * Audited by Professor Lee Made by Fransiskus * Forward Converter With Active Reset Circuitry Introduction 电源技术 Audited by Professor Lee Made by Fransiskus * Audited by Professor Lee Made by Fra