原创力文档- 1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
- 2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击 这里二次下载。
- 3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
- 4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
- 5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
- 6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
- 7、VIP文档为合作方或网友上传，每下载1次， 网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
BIK Shanghai International Ltd.
Tel: +86 21Fax: +86 21File No.: BIK.QC-FI-05
第 PAGE 1 页 共 NUMPAGES 8 页
Quality Control ChecklistWood Furniture
1. Rough Mill:
1.1 Check moisture content on lumber in kiln. Check moisture on plywood parts.
1.2 Check to insure rough cut parts are the correct length, width, height or thickness to allow for machining.
1.3 Check to insure there are no dead knots in the parts and that the live knots conform to product quality requirements.
1.4 Inspect for wind shake, splits, honeycombs, cracking, etc.
2. Lamination Department:
2.1 Insure that parts to be laminated are laminated on both sides before clamping.
2.2 Insure that grain direction is reversed on all parts being laminated.
2.3 Inspect for moisture content after the lamination process.
2.4 Inspect for rough cut sizes to insure allowances are made for machining, length, width, height or thickness.
3. Machine Department:
3.1 All parts need to be checked for proper size and machining according to the detail.
3.2 Inspect moisture content. (If moisture content is above 8% re-dry parts.)
3.3 All parts machined to spec sheets and FC standard spec Bk.
3.4 There are no parts splitting or cracking.
3.5 There are no open grains.
3.6 Check for parts being square when applicable.
3.7 Dry fit parts to check for proper fit.
3.8 Check all right angles.
3.9 Inspect tops with straight edge for warping.
3.10 Check Rab Parts for proper depth and consistent machining.
3.11 Check that all reveals are clean at 90% and uniform in size and length.
3.12 Inspect door style, door, side panels, parting rails, etc. For proper construction and warping (Use straight edge).
3.13 Check all board and mortised parts for proper size boring and tennon.
3.14 Check all miters and compound miters for consistency and fit.
3.15 Check boring for hardware, shelves and adjustable shelf hole spacing.
3.16 All reveal and tops are uniform in size.
3.17 Insure that bunn feet that cannot be turned into the car
文档评论（0）