武红霞的论文定稿.docVIP

学校代码 10722 1008034107 分类号 TB36 公开 fA武红霞 材料化学 工 学 王晓芳 fA 武红霞 材料化学 工 学 王晓芳2014年5月 利用黄金分割原则优化摩擦 材料的配方 Optimization the Formula of the Friction Material by the Pr i n ci pie of Golden Section 专业名称 学科门类 指导教师 提交论文日期 成绩评定 摘要 本文采用热压成型法制备了混杂纤维增强树脂基摩擦材料，在配方设计中采 用黄金分割原则对增强纤维含量进行优化，通过对样品进行摩擦磨损性能测试， 力学性能测试和物理性能测试，结果表明：配方1在0.764处，即碳纤维占0.16, 矿物纤维占0.05点为此配方纤维配比的最优点；其摩擦系数为0.40,磨损率为 0.26x10_7cm3/N-m,冲击强度为 5.21 J/cm2,硬度为 85 HRM,密度为 1.88 g/cm3o 配方2在0.382处，即矿物纤维占0.076,硅酸铝纤维占0.124点为此配方纤维配 比的最优点；其摩擦系数为0.40,磨损率为0.23x1 CT?cn?/Nm冲击强度为5.64 J/cm2,硬度为72 HRM,密度为1.79 g/cm3o研究结果表明利用黄金分割原则优 化摩擦材料的配方可以改善摩擦材料的性能。 关键字：摩擦材料；黄金分割；试验点；优化 Abstract By hot pressing molding in the preparation of the hybrid fiber reinforced polymer matrix friction materials, in the formula design of the reinforced fiber content by principle of golden section optimization, through the study of the friction and wear performance test of the sample, the mechanical properties testing and physical testing, the results show that the formula 1 in 0.764, the carbon fiber accounts for 0.16, mineral fibre the most advantages of 0.05 points for this formula ratio of fiber. Its friction coefficient is 0.40, the wear rate is 0.26x10 cm^-m, the impact strength of 5.21 J/cm^, hardness is 85 HRM, density of 1.88 g/enr. Formula 2 at 0.382, namely the mineral fibre accounts for 0.076, aluminum silicate fiber optimal point of 0.124 points for this formula ratio of fibc匸 Its friction coefficient is 0.40, the wear rate is 0.26x10 cm/N?m, the impact strength of 5.64 J/cm2, hardness is 72 HRM, density of 1.79 g/cm3. The results show that the golden principle was used to optimize the friction material formula can improve the performance of friction materials. Keywords: Friction material; Golden section; Test point; Optimize TOC \o 1-5 \h \z HYPERLINK \l bookmark4摘要 I 前言 ?1? HYPERLINK \l bookmark121文献综述 -2- 1.1摩擦材券斗 1.1.1摩擦材料的分类 -2- HYPERLINK \l bookmark161.1.2摩擦材料的技术要求 -2- HYPERLINK \l bookmark181.2摩擦材料发展简史 -2- HYPERLINK \l bookmark