塑料模具的塑料粒子专题bmc整理2012-2-28-杨帮伟110825_arteb_headlamp low beam reflector_1.pptVIP

下载本文档

43
0
约3.44千字
约 15页
2021-04-21 发布于北京
举报
版权申诉

塑料模具的塑料粒子专题bmc整理2012-2-28-杨帮伟110825_arteb_headlamp low beam reflector_1.ppt

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

Picture of Fluid flow Temperture at flow front Shear rate,bulk Pressure at injection location Clamp force Air traps Part name:Headlamp Low beam reflector_1 Date: 30.05.11 Part Information And Process Setup Part Details Process Setup Material BMC 304: BMC Inc (BMC+11%GF) Melt Temperature (oC) 90 Mold suface Temperature (oC) 166 Fill Time (s) 3.2 Velocity/Pressure Transfer (% volume) 99 Packing Pressure (MPa) 62 Project Area (cm2) 346.4cm2 (2cavity) 2.0mm Nominal Wall Thickness 139.2cm3 (2 cav) Part Volume 140X150X69 Part Size Aesthetical part Appearance Requirements Description Recommended processing BMC 304: BMC Inc (BMC+11%GF) Material properties BMC \ BMC 304(BMC Inc ) Viscosity Plot Material properties BMC \ BMC 304(BMC Inc ) BMC 304: BMC Inc (BMC+11%GF) Medium wall thickness is 2.0mm. Thickness distribution runner Setting FILL TIME Temperature At Flow Front Shear rate Pressure at injection location Pressure at end of fill Clamp force Air traps Volumetric shrinkage Conclusions and suggestions Result of moldflow analysis Click the plot, you will see the animated flow. Based on the flash of fluid flow in different range, we can see the filling state of plastic in cavity at each time and forecast the position of weld line and air traps, and we can judge if it appear short injection。 And it can show the position of vent for us to reference. Fluid flow Flash Fill of end Temperature at flow front is homogeneous. This result shows how the temperature of the flow front changes as the melt filling the cavity. so the range is small, we can overlay weld lines to show temperture when two flow front met. 8595 MAX SHEAR RATE (1/s) Shear rate distribution in plastic part thickness direction at the moment of filling ending is shown by different color.we can made a comparison of max Shear rate of material . The value is exceed normally appear on gatting system，eg:gate position. we can through change size of gate to control it. 62 10 PRESSURE (MPa) DURATION (s) HOL