注塑产品不良英语.docxVIP

磨痕 grinding defect 压伤 pressure hurt 刮伤 scratches 擦伤 abrasions 削伤 cut wounds 变形 deformation 破裂 crack 缩水 shrinking 缺胶 lack of plastic 缺料 short shot 针孔 microvoid 凹坑 dent 填充不足 short filling 翘曲 warpage 多孔 porosity 气孔 underfills 凸点 Protrusion 堵孔 plugged hole 油污 oil mark 手指印 fingerprint 模垢 contamination 披锋 Flash 困气 trapped gas 烧焦 burn 起苍 void 雾面 haze 焦痕 burn mark 糊斑 gas mark 结合线 weld line 毛边 burr flash 分型线毛边 parting line flash 合模线 parting line 涨模 parting line with flash 拉模 pulling mark 粘模 blush mold sticking part sticking 色差 chromatic aberration color deviation 光泽偏差 incorrect gloss level 光泽不良 lusterless 应力痕 stress mark 流痕 flow mark 料花 bloom 异色 冷料痕 cold slug 亮痕 shine mark light mark 白痕 white speck 水痕 water stain 顶针印 ejector pin marks 拖痕 drag mark 冲料痕 ejector mark 喷痕 jetting mark 异色点 color stain 污点 spot 斑点 speck stain 杂点 miscellaneous 黑点 black spot 黑线 black streak 银丝纹 sliver mark 污渍 dirty mark 白点 white spot 颗粒 particles 汽泡 air bubble 沾漆 remnant paint PU 漆脱落 PU paint peel 断字 fracture letter 偏位 wrong position 不完整 incompletion 模糊 illegible 印刷变形 deformation during printing 喷漆不均 uneven paint 褪色 color fading 偏斜 bias 歪斜 skew 折痕 crease 未倒角 no chamfer 倒角不良 bad chamfer 溢胶 melt overflow 表面模糊 surface haze 表面不平坦 unevenness 表面剥落 surface peeling 破碎 brittleness 扭曲 torsion 异色 discoloration 腐蚀/铁锈 corrosion 碰伤 bumps 进胶点未修平 gate flash trimming NG 进胶口点不良 dull spots near the sprue 孔径太大 hole over large 结合线明显 weldline obviously 尺寸过大 over dimension 尺寸过小 under dimension 扭力过低 low torque 定位不良 poor on line(offset) 拋光不良 poor polish 喷漆不良 poor paint 印刷不良 poor printing 整修不良 trimming NG 埋钉不良 poor insert 組裝不良 poor assembly 射出不良 poor injection 原料不良 poor raw material 外观不良 poor appearance 超音波结合不良 poor sonic welding 电镀不良 poor plating 铆钉脱落 rivet peel 铆钉松动 rivet slack 弹片脱落 spring plate peel 多装 overflow loading 少装 shortage loading 缺口 nick 磨损 abrasion 瑕疪 speck 斑点 speckle 间隙过大 excessive gap 水渍 water spots 错位 mismatch 脱色 discoloration 转载请注明出 自六西格玛品质论坛 ,本贴地 址: ead.php?tid=206037