JB_T 12942-2016管端挤压式高压管接头.pdf

ICS 23.040.60J 15JB备案号：56549—2017中华人民共和国机械行业标准JB/T12942—2016管端挤压式高压管接头End forming high pressure tube fitting2016-10-22发布2017-04-01实施中华人民共和国工业和信息化部发布 JB/T 12942—2016目次前言...2规范性引用文件3型式与尺寸.4型号与标记示例4.1型号，10管接头标记示例104.25技术要求5.1一般要求...材料要求..115.2加工要求....115.3锻件要求...115.4. 125.5爆放要求.... 125.6表面粗稳度要求，. 125.7表面处理要求5.8装配要求.... 126试验方法与检验规则，6.1试验方法..6.2检验规则..7标志、包装、运输和贮存7.1标志.. 137.2包装.. 137.3运输.. 147.4忙存，. 14附录A（规范性附录）管子挤压成型后的结构及尺寸. 15附录B（规范性附录)直管最小成形长度及弯管最小折成形长度...附录C（资料性附录）管子成型端装配力矩. 19附录D（资料性附录）管端挤压成形设备.. 20图 1管接头基本结构型式图 2米制螺较胶整垫密封编直通管接头结构..图3管螺纹胶垫密封端直通管接头结构，国55密封管娠纹端直通管接头结构.图5维螺纹端直通管接头结构图6直通管接头结构图 7直角管接头结构图8三通管接头结构图9过板管接头结构 JB/T129422016表5直通管接头尺寸单位为毫米系列工作压力管子外径MPaO.D.管接头型号ML2LyS,6WF-GV06LM12X1.539.024.010.012148WF-GV08LM14X1.540.025.011.01417 1031.5WF-GV10LM16X1.542.027.013.0L11912 WF-GV12LM18X1.543.028.014.0192215WF-GV15LM22X1.546.030.016.02427L18WF-GV18LM26X1.548.031.016.0273222 WF-GV22LM30X252.035.020.032362825WF-GV28LM36X254.036.021.0414135 WF-GV35LM45X263.041.020.0465042 WF-GV42LM52X266.043.021.055606WF-GV06SM14X1.545.030.016.0141763WF-GV08SM16X1.547.032.018.0171910 WF-GV10SM18X1.549.032.017.0 192212WF-GV12SM20X1.551.034.019.0222416WF-GV16SM24X257.038.021.0 273020WF-GV20SM30X266.044.023.0323640WF-GV25SM36X274.050.026.0414630WF-GV30SM42X280.054.027.0465031.538WF-GV38SM52X290.061.029.055603.7直角管接头结构及尺寸应符合图7和表6的规定。注：S、S,为六方对边尺寸，图7直角管接头结构 JB/T12942—2016表6直角管接头尺寸单位为毫米工作压力管子外径系列管接头型号MLyS,S,MPaO.D,6WF-WV06LM12X1.527.019.012.0 1214WF-WV08LM14X1.529.021.014.0121710WF-WV10LM16X1.530.022.015.0 141931.512WF-WV12LM18X1.532.024.017.0172215WF-WV15LM22X1.536.028.021.01927L18WF-WV18LM26X1.540.0 31.023.5243222 WF-WV22LM30X244.035.027.5273628WF-WV28LM36X247.038.030.536412535WF-WV35LM45X256.045.0 34.541 5042 WF-WV42LM52X263.051.040.05060WF-WV06SM14X1.531.023.016.0121700WF-WV08SM16X1.532.024.017.014196310WF-WV10SM18X1.534.025.017.5172212 WF-WV12SM20X1.538.029.021.5172416WF-WV16SM24X243.033.0 24.52430 20WF-WV20SM30X248.037.026.5364025WF-WV25SM36X254.042.030.0364630WF-WV30SM42×262.049.0