点阵时钟C程序.docVIP

32*16点阵万年历C程序 #include reg52.h#define uchar unsigned char #define uint unsigned int#define LINE P2//定义行线IO口，即74HC154控制端sbit DATA1=P1^4;//74HC595数据端sbit CLK=P1^5;//74HC595移位脉冲端sbit CLKR=P1^6;//74HC595数据锁存端sbit BBT =P2^7;//蜂鸣器引脚sbit SCLK=P1^2;//DS1302移位脉冲端sbit DATA=P1^1;//DS1302数据端sbit RST=P1^0;//DS1302控制端sbit key=P3^4;//功能按键sbit key1=P3^3;//加+按键sbit key2=P3^2;//加+按键uchar line;//行扫描变量uchar move;//移位次数变量uchar mov;//年月日时间左移变量，即移8次将1个字移完后加1uchar yin;//按键计数器变量，一共10次，即功能按键有10种功能uchar lk;//扫描两行还是1行变量uchar readvalue;//DS1302转换结果变量uchar shi,fen,nian,yue,ri,xin;//分别为：小时/分钟/年/月/日/星期变量uchar shin=12,fenn;//闹钟的小时与分钟变量bit dian;//主时间小数点位变量bit shr,a,b,c,d,e,f,g,h,i;//按键对应的10种功能位变量bit flag;//主程序与调整时间切换变量，即进入调整时间部分就不进入主时间部分bit flag1;//闹钟标志位变量bit clockbiao;//闹钟响铃主标志位uchar BUF[19];//4组缓存数组以便动态更改数据/******************************************************//**************点阵0-9代码（8*6点阵）******************//******************************************************/uchar code table[]={0x00,0x0E,0x11,0x11,0x11,0x11,0x11,0x0E,//00x00,0x04,0x0C,0x04,0x04,0x04,0x04,0x0E,//10x00,0x0E,0x11,0x01,0x02,0x04,0x08,0x1F,//20x00,0x0E,0x11,0x01,0x06,0x03,0x11,0x0E,//30x00,0x06,0x06,0x0A,0x0A,0x12,0x1F,0x02,//40x00,0x1F,0x10,0x10,0x1E,0x01,0x01,0x1E,//50x00,0x0E,0x11,0x10,0x1E,0x11,0x11,0x0E,//60x00,0x1F,0x01,0x02,0x02,0x04,0x04,0x08,//70x00,0x0E,0x11,0x11,0x0E,0x11,0x11,0x0E,//80x00,0x0E,0x11,0x11,0x0F,0x01,0x01,0x1E,//9};/******************************************************//**********两个小数黑屏及坚线代码8*6点阵）*************//******************************************************/uchar code table1[]={0x00,0x0C,0x0C,0x00,0x00,0x0C,0x0C,0x00,//为两个小数点:0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//为黑屏代码0x00,0x00,0x00,0x1E,0x1E,0x00,0x00,0x00//为两坚线-};/******************************************************//****此数组为74HC154译码器代码（注也可以不用数组）*****//******************************************************/uchar code table2[]={0xf0,0xf1,0xf2,0xf3,0xf4,0xf5,0xf6