机械制造专业毕业论文--人工髋关节模拟试验机机械传动部分研制.docVIP

摘要 本课题是对人体髋关节模拟试验机机械传动部分的研制。模拟试验机是一台集机、电、液技术于一体的专用台架试验设备。试验机的工作原理是将股骨头和髋臼部件试样按照其正常位置安装于试验台上，通过试验装置使两者之间产生规定的随时间变化的负载及相对角运动。该机械设计时考虑的主要因素是使其在实验室环境中能够正确模拟人体髋关节的实际运动工况，以使试件在试验过程中产生的摩擦机理、磨损形式与实际使用条件下相一致，从而可以准确、可靠地测试人工关节材料的生物摩擦学特性参数，为临床应用提供指导性试验数据。根据以上要求设计出试验机的总装配图。该试验机要求的最大试验载荷为1t，要求主轴转速为60rpm。假设作用在股骨头头部的载荷为1t，则可以算出最大阻力。选则直径为50mm的股骨头，求出最大扭矩，由此确定电机的功率从而计算出最小轴径。根据最小轴径初选各个零件的尺寸。通过校核确认其安全以确保试验机正常运转。电机运转时通过联轴器带动主轴旋转，从而带动固定在主轴轴端的偏心轮转动，试件座安装在摆轴上和摆轴一起饶中心轴线转动。使得由关节球支架固定在试件座上的关节球头和髋臼试件之间产生摩擦，从而达到试验的目的。其中髋臼试件由骨水泥固定在髋臼座上，冲击载荷由液压缸提供作用于自定心轴上，通过髋臼支架最终作用在关节球头上，加上关节球头随试件座绕中心线转动。这样实现模拟人体髋关节的实际运动，使其产生的摩擦机理、磨损形式与实际使用条件下相一致，以达到设计该试验机的初衷。 关键词：关节试验机 ;模拟试验 ;人体髋关节 ;摩擦机理 Abstract A hip simulator had been designed and manufactured in this study. Simulation test is a set of mechanical, electrical, fluid technology in one of the special bench test equipment.The principle of the simulator is fit the stock bone and the part test specimen to its normal position in the test platform, causing the variation load changing with the time and the relative angular motion between them through the test equipment. The primary factor which this machine design considered is whether it can simulate the human body coxa correctly in the laboratory environment, so that the friction mechanism, the attrition form of the test sample which produces in the testing with the actual exploitation conditions under consistent, thus may be accurate, reliably test the biological friction of the artificial joint material, provides the guidance tentative data for the clinical practice. Designs the testing machine according to the above request the assembly drawing. The biggest experimental load of this testing machine requests is 1t, the main axle rotational speed is requests 60rpm. The supposition function in the thighbone leaders department load is 1t, then may figure out the biggest resistance. Elects then the diameter is the 50mm stock bone, extracts the maximum torque, from this determines the electrical machinery the power thu