周期对称结构的静力分析实例.docVIP

/filname,ch08 /title,static analysis of compressor structuren with hole /prep7 et,1,solid45 mp,ex,1,1.15e5 mp,prxy,1,0.30782 mp,dens,1,4.48e-9 k,1,226,,208.8 k,2,226,,258.7 k,3,157,,258.7 k,4,237.5,,220.3 k,5,229.2,,220.3 k,6,237.5,,208.8 k,7,126,,276.7 k,8,138,,276.7 k,9,102.5,,263 k,10,102.5,,248.7 k,11,237.5,,273.8 k,12,237.5,,264.1 k,13,135,,248.7 k,14,243.85,,273.8 k,15,243.85,,254.8 k,16,229.2,,254.8 k,17,162.5,,264.1 /pnum,kp,1 /pnum,line,1 /number,2 /view,1,,,-1 /auto,1 lstr,1,2 lstr,2,3 lstr,1,6 lstr,6,4 lstr,4,5 lstr,5,16 lstr,16,15 lstr,15,14 lstr,14,11 lstr,11,12 lstr,12,17 lstr,8,7 lstr,7,9 lstr,9,10 lstr,10,13 lplot ltan,11,8 !创建切线 ltan,2,13 al,all /pnum,line,0 /pnum,kp,0 k,18,,,, k,19,,,300 vrotat,all,,,,,,18,19,60 /view,1,1,1,1 /auto,1 save wprot,30 cyl4,200,0,10,,,,300 !注意圆柱的深度方向是沿工作平面坐标系 !z向的； vsbv,1,2 save /view,1,,,-1 /auto,1 wpcsys,-1,0 lstr,18,19 flst,2,2,8 fitem,2,0,0,0 fitem,2,220,0,0 circle,p51x,,,,60 flst,2,2,8 fitem,2,0,0,0 fitem,2,180,0,0 circle,p51x,,,,60 lsla,u !将与面关联的线从选择集中去除 /pnum,line,1 adrag,53,,,,,,52 adrag,54,,,,,,52 /pnum,line,0 allsel aslv,u vsba,all,all allsel wprot,,90 wprot,,,21 vsbw,all wprot,,,9 vsbw,all wprot,,,9 vsbw,all ldele,52,,,1 !删除轴线 csys,1 !激活坐标系转为总体柱坐标系 vsel,s,loc,x,180,220 cm,holevol,volu allsel vplot save !定义周期对称分析选项 !定义高低角度组件 !即周期对称结构的对称边界 !组件命名时，前面的cyclic即为组件根名 asel,s,loc,y,0 cm,cyclic_m01l,area asel,s,loc,y, 60 cm,cyclic_m01h,area allsel cyclic,6,60,1,’cyclic’ !此步为指定周期对称分析选项 !连接线和面以便于映射网格划分 esize,3 cmsel,s,holevol vsel,r,loc,y,21,30 aslv,s wpcsys,-1,0 wprot,30 wpoff,200 cswpla,11,1 asel,u,loc,z,264.1 asel,u,loc,z,258.7 asel,u,loc,x,10 csys,1 asel,u,loc,y,30 accat,all lsla,s lsel,r,loc,z,264.1 lccat,all lsla,s lsel,r,loc,z,258.7 lccat,all !生成网格，采用扫略网格划分 type,1 mshape,0,3d vsel,s,loc,y,0,21 vsweep,all vsel,s,loc,y,21,30 vsel,u,loc,x,180,220 vsweep,all cmsel,s,holevol vsel,r,loc,y,21,30 vsweep,all vsel,s,loc,y,0,30 asel,s,acca adele,all lsel,s,lcca ldele,all csys,4 vsymm,y,all,,,,0,0 allsel nummrg,all numcmp