带式输送机传动装置二级斜齿圆柱齿课程.docVIP

带式输送机传动装置二级斜齿圆柱齿轮减速器设计(课程设计) 设计任务书 ? 设计题目:带式输送机传动装置二级斜齿圆柱齿轮减速器设计 ?? 设计带式输送机传动系统?采用两级圆柱齿轮减速器的传动系统参考方案(见图)? ?? 带式输送机由电动机驱动?电动机1通过联轴器2将动力传入良机圆柱齿轮减速器3,在通过联轴器4,将动力传至输送机滚筒5,带动输送带6工作? 原始数据: 输送带有效拉力F=3600N 输送机滚筒转速n=60r/min (允许误差±5%) 输送机滚筒直径D=360mm 减速器设计寿命为10年(250天/年)? 工作条件: 两班制(15h/天),常温下连续工作;空载起动,工作载荷平稳,单向运转;三相交流电源,电压为380/220伏? 设计任务:1?减速器装配图1张(0号或1号图纸); ????????? 2?零件图2张(低速轴及上面大齿轮,3号或号图纸) ????????? 3?设计计算说明书一份 如需此设计请联系客服QQ584230580 全套设计包括:开题报告,课题简介,装配图,零件图,设计说明书,答辩提纲等.欢迎朋友选购.均为电子版(图纸CAD,说明书WROD),由于设计类目太多(通过答辩的机械类毕业设计1W于套,计算机类1W于套含源程序,其他各专业7W于套),一一列出来比较繁琐,而且豆丁交易没保障,请购买时联系本站唯一客服QQ:584230580支持淘宝安全放心,先论文后付款,价钱最低质量最好,把您的风险降到最低,让您无后顾之忧,选择我们绝不后悔,保证您用最低的价钱买到质量最好的论文? 我们为广大的毕业生提供了良好的服务,也赢得了历届毕业生的一致好评,我们有3年从事毕业设计指导工作的经验,价格公道,信誉好,支付宝交易先货后款,可以请大家放心购买,并含有视频教程跟售后服务?是各位毕业生们的第一选择!欢迎各位前来咨询 Acknowledgments The authors would like to thank Johns Hopkins University for the TC-1 cells. This work was supported by a National Health Research Institutes intramural grant (IV-103-PP-22) and grants from the National Science Council, which were awarded to Y.C. Song (NSC 99-2321-B-400-004-MY3) and S.J. Liu (NSC 103-2321-B-400-008). Author Contributions Y.C.S. and S.J.L. designed the studies. Y.C.S. performed the research and analyzed the data. Y.C.S. and S.J.L. wrote the manuscript. Additional Information C57BL/6 mice were immunized subcutaneously (s.c.) once with 1 μ g of peptide mixed with or without 10 μ g of CpG adjuvant. After one week, splenocytes were harvested, and the response of IFN-γ -secreting cells was determined by ELISPOT after 48 h of peptide stimulation. Briefly, 2 × 105 splenocytes were incubated with 1 μ g/ml irrelevant peptide or RAH peptide in an anti-IFN-γ -coated polyvinylidene fluoride (PVDF) plate for 48 h. After incubation, the cells were removed, and a biotinylated anti-IFN-γ Ab (eBioscience, San Diego, CA, USA) was added to each well. The plates were incubated at 37 °C for 2 h. Following the addition of the avidin-HRP reagent (eBioscience, CA, USA), the assay was