模具标准件设计与标注规范课程.docVIP

精密模具设计部技术通报 摘要:模具标准件设计与标注规范 文件编号:TD(Tooling Department)1008-1 为做到模具结构规范统一,现制定模具标准件设计与标注规范如下: 一:小水口唧嘴 材质:S55C 标准编号:SB130 尺寸规格:￠130*60.00 在三板模中,我们采用上图唧嘴?标注规范示例可参考:works\技术资料\标准件\ SB小水口唧嘴.dwg (注:因库存圆钢料略小,与加工协商将外径由Ф130mm改为Ф129mm?2003/12/06,曾盛渠更改) 二,隔热板TI350320, TI350280 尺寸规格:350*320*6, 350*280*6热板,请另外出图works\技术资料\标准件\常用隔热板.dwg 三:运输板 材质:S55C 标准编号:LB13025, LB6520 尺寸规格:130*25*8, 65*20*8 标注规范示例可参考:works\技术资料\标准件\运输板.dwg 四:急回机构 1, 急回击杆 材质:718H 标准编号:JH-1 尺寸规格:200*30*23.5 2, 击杆导正块2344 标准编号:JH-2 尺寸规格:27*23.3*18.003, 摆杆 材质:718H 标准编号:JH-3 尺寸规格:75.40*25*22.00 4, 轴承套 材质:718H 标准编号:JH-4 尺寸规格:￠16*23 标注规范示例可参考:works\技术资料\标准件\急回机构.dwg 五:排气片 材质:S136 (HRC47~49) 标准编号:EP-1, EP-2 尺寸规格:17.12*16.00*2.06, 17.12*16.00*1.50works\技术资料\标准件\排气片标准件.dwgAcknowledgments The authors would like to thank Johns Hopkins University for the TC-1 cells. This work was supported by a National Health Research Institutes intramural grant (IV-103-PP-22) and grants from the National Science Council, which were awarded to Y.C. Song (NSC 99-2321-B-400-004-MY3) and S.J. Liu (NSC 103-2321-B-400-008). Author Contributions Y.C.S. and S.J.L. designed the studies. Y.C.S. performed the research and analyzed the data. Y.C.S. and S.J.L. wrote the manuscript. Additional Information C57BL/6 mice were immunized subcutaneously (s.c.) once with 1 μ g of peptide mixed with or without 10 μ g of CpG adjuvant. After one week, splenocytes were harvested, and the response of IFN-γ -secreting cells was determined by ELISPOT after 48 h of peptide stimulation. Briefly, 2 × 105 splenocytes were incubated with 1 μ g/ml irrelevant peptide or RAH peptide in an anti-IFN-γ -coated polyvinylidene fluoride (PVDF) plate for 48 h. After incubation, the cells were removed, and a biotinylated anti-IFN-γ Ab (eBioscience, San Diego, CA, USA) was added to each well. The plates were incubated at 37 °C for 2 h. Following the addition of the avidin-HRP reagent (eBios