FX30青贮收割机应用分析.pptVIP

下载本文档

4
0
约9.96千字
约 47页
2016-08-03 发布于湖北
举报
版权申诉

FX30青贮收割机应用分析.ppt

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

Operators course Zedelgem Harvester Training 五、竞争对手六、工作效率七、价格 790/900牵引青贮收获机牵引青贮收获机竞争对手 1: Language, Metric / Imperial, engine speed and bargraph, Airco, Rotary brushes, Spout slow speed, Simultaneous movement flipper, User messages, High capacity hydraulics, screen contrast 2: Attachment width, semi auto HHC: ground level maximum position pressure just above ground level pressure just below maximum position 3: Ground speed tuning 4: Crop processor 5: Date time Enter E-value mode with ENTER and Ha Shaft turning - top value is rpm, (bottom value is calibrated max with engine) Shaft in rest - bottom value is E-value CPU Minimum trigger point: (no metal in front), (not 130) 149 (CPU 01/01/1996) 170 (CPU 01/01/1996) CPU maximum trigger point (metal in front) 200 (all) Blower is not used Knives: Grass: Busatis #: Lund #:(Better) Corn: Busatis #:Shearbar: Grass: Busatis #: Lund #:(Better) parts only Corn: Busatis #: Busatis #:(heavy duty) parts only Stone: Grass: Bay State #:(for Busatis) Bay State #:(for Lund, grey) Corn: Bay State #: The attachment is clamped on by a tierod with 2 nuts. An hydrostatic pump drives the attachment drive gearbox on the left hand side of the Chopperbody. The length of cut is variable between 4 and 10 mm in the low range and between 8 and 20 mm in the high. The selection between high and low is made on the HydroLOC gearbox on the right hand side of the Chopperbody. On the attachment drive gearbox are 2 output shafts:1. 300-750 rpm for the pick-ups, 300N6 corn head and the snapper headers2. 500-1260 rpm for the RI corn headers and DC510 The hydrostatic motor is blocked by a stop valve after a metal detection. When the lever on the HydroLOC gearbox is push to the inside the low range is selected. When it is pulled to the outside the high range is selected. The Decal s