指PG制螺纹.docVIP

指PG制螺纹，常用的有M制螺纹。PG螺纹属于钢管用螺纹，详细标准可查DIN 40430标准.Pg Thread DIN 40430Steel Conduit Thread For cable diametermm电缆直径毫米Thread Size螺纹尺寸 Major Diametermm TappingDrill Size 攻丝钻头尺寸Pitch螺距mm 6,0 Pg 7 12,5 11,3 1,27 8,0 Pg 9 15,2 13,9 1,41 10,0 Pg 11 18,6 17,3 1,41 12,0 Pg 13,5 20,4 19,1 1,41 14,0 Pg 16 22,5 21,2 1,41 18,0 Pg 21 28,3 26,8 1,59 25,0 Pg 29 37 35,5 1,59 32,0 Pg 36 47 45,5 1,59 38,0 Pg 42 54,0 52,5 1,59 43,0 Pg 48 59,3 57,8 1,59 On 31.12.1999 the safety standard VDE 0619 which included the standards DIN 46319 for metric sizes and DIN 46320 for PG-sizes were withdrawn. On 01.01.2000 the new standard DIN EN 50262 came into force. The new standard uses the new metric sizes. In the transitional period - until 01.03.2001 - the PG-standard could still be used. For replacement PG-items may still be used. The ten sizes PG 7 / 9 / 11 / 13,5 / 16 / 21 / 29 / 36 / 42 and PG 48 were replaced by eight new metric sizes, i.e. M 12 / 16 / 20 / 25 / 32 / 40 / 50 and M 63. No direct conversion is possible! By this new standard a suitable solution was not achieved. Possibilites for a conversion: PG Size Major Diameter 大径 mm For cable diametermm（电缆直径） Conversion to metricmm 转换为公制 Pg 7 12,5 6,0 M 12 Pg 7 12,5 6,0 M 16 Pg 9 15,5 8,0 M 16 Pg 11 18,6 10,0 M 20 Pg 13,5 20,4 12,0 M 20 Pg 13,5 20,4 12,0 M 25 Pg 16 22,5 14,0 M 20 Pg 16 22,5 14,0 M 25 Pg 21 28,3 18,0 M 25 Pg 21 28,3 18,0 M 32 Pg 29 28,3 18,0 M 32 Pg 29 28,3 18,0 M 40 Pg 36 47,0 32,0 M 50 Pg 42 54,0 38,0 M 50 Pg 42 54,0 38,0 M 63 Pg 48 59,3 43,0 M 63 Wrench Size for Cable Connection扳手尺寸的电缆连接 Connecting Thread连接螺纹 Wrench Size扳手尺寸mm Old老的 PG7 SW 15 PG9 SW 19 PG11 SW 22 PG13,5 SW 24 PG16 SW 27 PG21 SW 33 PG29 SW 42 PG36 SW 53 PG42 SW 60 PG48 SW 65 New新的 M12x1,5 SW 15 M16x1,5 SW 19 M20x1,5 SW 24 M25x1,5 SW 30 M32x1,5 SW 36 M40x1,5 SW 46 M50x1,5 SW 55 M63x1,5 SW 66