环氧酯铁红锌黄底漆.doc

Intended Uses 用途 环氧酯铁红底漆, 适用于黑色金属表面,而环氧酯锌黄底漆适用于铝和铝镁合金表面,这二种底漆与磷化底漆配套,可提高漆膜的耐盐雾及防锈性能,这两种底漆均能形成具有良好附着力的坚韧涂膜. Iron red epoxy ester is suited for ferrous metal surface.andzine yellow epoxy ester primer is surted for aluminium and alum-inium magnesium surface. Both primes can match with etching primer which with improve films resistance to moisture, salt fog, and corrosion, Eatch of them forms atough, durabl coati- ng with good adhesion. Product Information产品简介 铁红色或淡黄色 Iron red or light yellow Application details 产品数据 Volume Solids 固体份 ≥46% Dry Flm Thickness干膜厚度 40microns equivalent to 87 microns of wet film 40微米相当于87微米湿膜 Theoretical Coverage 理论涂布率 8.5m2 /Kg 8.5平方米/公斤 Practical Coverage 实际涂布率 Allow appropriate loss 允许适量损耗 Storage and Handling 施工详述 Mix Radio 混合比 One package 单罐装 Method of Application 施工方法 Airless Spray 无空气喷涂 Recommended 推荐采用 Brush or Roller 涂刷或辊涂 Recommended 推荐采用 Conwentional Spray 传统喷涂 Recommended 推荐采用 Thinner 稀释剂 SC003 Cleaner 油漆设备清洗剂 SC003 Pot Life 使用期 Not limit 没有限制 Storage 贮存期 One year 一年 Drying time 干燥时间 Substrate Temperature 底材温度 Touch Dry 表干 （h） Hard Dry 硬干 h） Over coating Interval 覆涂间隔 Min最短 Max最长 25℃ 2 24 24 hours 小时 14days 天 Storageand Handling 贮存与管理 Storage 贮存 Store in cool and dry conditions 贮存于阴凉干燥处 Pack size 包装规格 25Kg in 20 liter container 25公斤装于20公升容器中 Flash Point 闪点 30℃ Specific Gravity 比重 Approx 1.3-1.4Kg/L 约1.3-1.4公斤/公升 Specification and Surface preparation 技术要求及表面处理 The steel surface: Blast clean to Swedish Standard SIS055900 Sa2.5 or rust-removed manually or with power tool to St3 钢材表面：喷砂处理达瑞典标准 SIS055900 Sa2.5级或手工、动力工具除锈至St3级. Limitations 限制 Recommend coat: Spray two coats with high-pressure airless spray and dry film thickness should reach 80 microns 建议涂装道数：高压无空气喷涂二道，干膜厚度达80微米。 Subsequent coat: Epoxy resin paint, chlorinated rubber paint, chorosulphonated polyethylene paint etc. 后道配套涂料：环氧树脂涂料，氯化橡胶涂料，醇酸树脂涂料，氯磺化聚乙烯涂料等。 Safety Precautions 安全措施 This product should be used in painting area by pe