05机械制造类外文资料.docVIP

  1. 1、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。。
  2. 2、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载
  3. 3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
  4. 4、该文档为VIP文档,如果想要下载,成为VIP会员后,下载免费。
  5. 5、成为VIP后,下载本文档将扣除1次下载权益。下载后,不支持退款、换文档。如有疑问请联系我们
  6. 6、成为VIP后,您将拥有八大权益,权益包括:VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
  7. 7、VIP文档为合作方或网友上传,每下载1次, 网站将根据用户上传文档的质量评分、类型等,对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
05机械制造类外文资料

2.4 Compression and Transfer Molds 2.4.1 Compression Molding Compression molding is the basic forming process where an appropriate amount of material is introduced into a heated mold, which is subsequently closed under pressure. The molding material, softened by heat, is formed into a continuous mass having the geometrical configuration of the mold cavity. Further heating (thermosetting plastics) results in hardening of the molding material. If thermoplastics are the molding material, hardening is accomplished by cooling the mold. Fig. 2-6 illustrates types of compression molding. Here the molding compound is placed in the heated mold. After the plastic compound softens and becomes plastic, the punch moves down and compresses the material to the required density by a pressure. Some excess material will flow (vertical flash) from the mold as the mold closes to its final position. Continued heat and pressure produce the chemical reaction which hardens the compound. The time required for polymerization or curing depends principally upon the largest cross section of the product and the type of molding compound. The time may be less than a minute, or it may take several minutes before the part is ejected from the cavity. Since the plastic material is placed directly into the mold cavity, the mold itself can be simpler than those used for other molding processes. Gates and sprues are unnecessary. This also results in a saving in material, because trimmed-off gates and sprues would be a complete loss of the thermosetting plastic. The press used for compression molding is usually a vertical hydraulic press. Large presses may require the full attention of one operator. However, several smaller presses can be operated by one operator. The presses are conveniently located so the operator can easily move from one to the next. By the time he gets around to a particular press again, that mold will be ready to open. Fig. 2-6 Types of Compression Moldin

文档评论(0)

tiangou + 关注
实名认证
文档贡献者

该用户很懒,什么也没介绍

1亿VIP精品文档

相关文档