- 1、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。。
- 2、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
- 4、该文档为VIP文档,如果想要下载,成为VIP会员后,下载免费。
- 5、成为VIP后,下载本文档将扣除1次下载权益。下载后,不支持退款、换文档。如有疑问请联系我们。
- 6、成为VIP后,您将拥有八大权益,权益包括:VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
- 7、VIP文档为合作方或网友上传,每下载1次, 网站将根据用户上传文档的质量评分、类型等,对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
2014092授予同等学力人员临床医学硕士专业学位
授予同等学力人员临床医学硕士专业学位
实施办法
(讨论稿)
为促进我国临床医学应用型人才的培养,拓宽临床医师获得硕士学位的途径,实现住院医师规范化培训与临床医学硕士专业学位研究生教育的有机衔接,根据《国务院学位委员会关于授予具有研究生毕业同等学力人员硕士、博士学位的规定》和《临床医学专业学位试行办法(一)包括政治理论、基础课专业,总门数不少于5门政治理论、基础课学位授予单位聘请至少三名具有高级专业技术职务的专家为论文评阅人论文评阅人中至少有一位是学位授予单位以外的专家不得聘请申请人的导师作为论文评阅人。评阅学位授予按学科、专业组成答辩委员会,答辩委员会应由至位具有临床医学副教授或副主任医师以上职称的专家(含临床医学硕士生导师名申请人的导师)组成以论文答辩的形式考核申请人的临床科研能力。拥护中国共产党的领导,拥护社会主义制度,热爱祖国,具有良好的医德医风,团结协作,身体健康,愿为我国现代化建设和临床医学事业而献身;具有较强的临床分析和思维能力,能对下级医师进行业务指导;
掌握本学科坚实的基础理论和系统的专业知识;
能结合临床实际,学习并掌握临床科学研究的基本方法,完成一篇学位论文并通过答辩;
掌握一门外国语,具有较熟练阅读本专业外文资料的能力。
学位课程学位论文答辩由学位授予单位的学位评定委员会审核批准授予专业学位。
manufacturers drawings bolt fastened in the cylinder and outer cylinder. Cylinder cylinder in the drain pipe installation and measuring component leads. 6.4.4.3 blade carrier, partitions and lower installation check the sealing ring of the seal and springs, which shall conform to the technical requirements manufacturers drawings. Cylinder gasket on the mounting brackets supporting the Group assembled, the lugs shall be no Burr on the surface, and other debris. Department suite in place to measure surface and inner cylinder surface height difference, compared with the original values confirm the location. 6.4.4.4 lower bearing and thrust bearing installation clean bearing and bearing, thrust bearing joints, clean them with a thin layer of turbine oil, and then lifting it to bits. 6.4.4.5 high and middle pressure cylinder over it to the end (for high pressure rotor and low pressure change flange gasket without connection unit) rotors and rotor flange gasket connection and there is no connection, so the rotor in place cases, rotors in place must be high and middle pressure cylinder together with the Chamber over it to the end. Jack in the box that are installed on a push-pull device of adjusting the high and medium pressure cylinder to end over and around to set up indicators to monitor data, general data about the difference must not exceed 0.02mm. To prevent cylinder about out of sync over the situ
文档评论(0)