[PEEK注塑加工成型.ppt

PEEK 注塑加工成型 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile . Copyright 2004-2011 Aspose Pty Ltd. PEEK加工的可能性 PEEK 为半结晶热塑性材料，熔点343℃ 结晶度为30% 适用于“所用”热塑性材料的成型加工技术 挤出，注塑、模压、喷涂、吹塑、发泡…… Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile . Copyright 2004-2011 Aspose Pty Ltd. 影响注塑产品品质的因素 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile . Copyright 2004-2011 Aspose Pty Ltd. 高分子聚合物的形态 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile . Copyright 2004-2011 Aspose Pty Ltd. 结晶型塑胶的加工范围 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile . Copyright 2004-2011 Aspose Pty Ltd. 注塑加工示意图 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile . Copyright 2004-2011 Aspose Pty Ltd. 注塑成型指南 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile . Copyright 2004-2011 Aspose Pty Ltd. 吸水率 0.5% w/w（ 大气水） 干燥要求：0.02% w/w ------露点为-40° 150℃ 3hours 160℃ 2hours 干燥 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile . Copyright 2004-2011 Aspose Pty Ltd. 螺杆清洗 升温清洗（针对其他低温原料残留） 先将料筒的温度加热到该料的温度 加入PP+30%GF（专用螺杆清洗剂） 冲洗（至无黑点） 清空料筒 升高温度至PEEK加工温度 加入PP+30%GF冲洗（洁净后） 清空料筒 加入洁净的PEEK原料，清空PP+30%GF残留 试生产 降温清洗（针对PEEK原料残留） PEEK生产完成 清空料筒 加入PP+30%GF（专用螺杆清洗剂） 冲洗至无PEEK残留 以20℃为一个等级做降温清洗 直至降温至300℃ 等待其他原料的生产 积碳清洗方法（针对PEEK 积碳原料残留） 物理清洗 专用螺杆清洗剂清洗 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile . Copyright 2004-2011 Aspose Pty Ltd. 注塑加工条件 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile . Copyright 2004-2011 Aspose Pty Ltd. PEEK产品壁厚与注塑周期 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile . Copyright 2004-2011 Aspose Pty Ltd. 温度控制 注塑机料筒温度和喷嘴温度 —— 料筒的温度范围：400℃（特种规格要求达到450℃） —— 喷嘴加热要求：加热圈