12864函数操作..docVIP

module_12864.h #include reg52.h #define IO_12864 P0 //定义12864的数据端口 sbit RS_12864 = P2^5; //定义命令数据寄存器选择端 sbit RW_12864 = P2^6; //定义定义读写控制端 sbit E_12864 = P2^7; //定义使能端 sbit RST_12864 = P2^2; //定义复位端 void delay_12864(unsigned int ); //延时子函数原型 void busychk_12864(void); //忙检测子函数原型 void wrtcom_12864(unsigned char); //写命令子函数原型 unsigned char reddat_12864(void); //读数据子函数原型 void wrtdat_12864(unsigned char); //写数据子函数原型 void drawpic_12864( unsigned char*); //绘图子函数原型 void drawdot_12864(unsigned char,unsigned char,unsigned char);//画点子函数原型 //画矩形子函数原型 void drawrec_12864(unsigned char,unsigned char, unsigned char,unsigned char,unsigned char); void clnGDR_12864(void); //清空GDRAM子函数原型 //输入短字符串子函数原型 void inputchars_12864(unsigned char,unsigned char,unsigned char*); void scroll_12864(unsigned char*); //输入长字符串卷动子函数原型 void initial_12864(void); //12864初始化子函数原型 modlule_12864.c //*延时子程序，最大延迟时间为65ms void delay_12864(unsigned int del){ unsigned int i; for(i = 0; i del; i++){;} } //*忙检测，若忙则等待，最长等待时间为60ms void busychk_12864(void){ unsigned int timeout = 0; E_12864 = 0; RS_12864 = 0; RW_12864 = 1; E_12864 = 1; while((IO_12864 0x80) ++timeout != 0); //忙状态检测，等待超时时间为60ms E_12864 = 0; } //写命令子程序 void wrtcom_12864(unsigned char com){ busychk_12864(); E_12864 = 0; RS_12864 = 0; RW_12864 = 0; IO_12864 = com; E_12864 = 1; delay_12864(50); //使能延时50us!!!注意这里，如果是较快的CPU应该延时久一些 E_12864 = 0; } //读数据子程序，返回一个字节的数据 unsigned char reddat_12864(void){ unsigned char temp; busychk_12864(); E_12864 = 0; IO_12864 = 0xff; //IO口置高电平，读引脚 RS_12864 = 1; RW_12864 = 1; E_12864 = 1; delay_12864(50); //使能延时50us!!!注意这里，如果是较快的CPU应该延时久一些 temp = IO_12864; return temp; } //写数据子程序 void wrtdat_12864(unsigned char dat){ busychk_12864(); E_12864 = 0; RS_12864 = 1; RW_12864 = 0; E_12864 = 1; IO_12864 = dat; delay_12864(50); //使能延时50us!!!注意这里，如果是较快的CPU应该延时久一些 E_12864 = 0; } //显示图片函数，参数时图片的地址，图片必须是128*64像素的逐行逐行的点阵信息。 void drawpic_12864( unsigned char *pPicture ){ unsigned char j, k ; wrtcom_12864(0x34); //在写GDRAM的地址之前