structural technical report1- penn state engineering（结构技术report1 -宾夕法尼亚州立大学工程）（14页）.docVIP

下载本文档

9
0
约2.27万字
约 14页
2017-01-17 发布于湖南
举报
版权申诉

structural technical report1- penn state engineering（结构技术report1 -宾夕法尼亚州立大学工程）（14页）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

Structural Technical Report #1 By Robert Whitaker Executive summary This report covers the structural concepts used in designing Parkview at Bloomfield Station, a six story residential apartment and parking garage in Bloomfield, New Jersey. It encompasses gravity and lateral loading analysis checks. Structural Overview The structural system for Parkview at Bloomfield Station is a roof composed of light gage roof trusses spaced 2’ on center (oc) spanning front to back, panelized bearing light gage walls 4” and 6” wide continuously capped with a steel tube for load distribution purposes and a 16” deep D500 Hambro? floor system. The main lateral force resisting system for the building is a shear wall system provided by thin cross bracing straps attached to the light gage bearing walls. Finally, a 4” slab-on-grade foundation with 2’-6” continuous footings makes up most of the building’s foundation; however, larger 4’x4’ spread footings are utilized below column point loads. The precast garage is structurally separate, and it will not be considered in the design review. Code Overview The design of the structure was in accordance with the International Building Code (IBC) 2000 with New Jersey amendments, the New Jersey Uniform Construction Code, and local county and township requirements (there were no structural changes due to these amendments). The dead, live, and wind loads used in the design were proven to be adequate based on the loadings found in ASCE 7-98 for gravity and lateral load. Calculation Overview All spot checks performed on structural components in the building showed that the members were adequately sized for the calculated loads. The structural columns, the Hambro floor joists, the tube steel top plates, and the shear wall assemblies were all determined to be adequately sized for both ASD and LRFD loadings. It was also determined that seismic design controlled over wind in the lateral analysis. A more in depth analysis of the lateral