L CD液晶显示程序精品参考资料.docVIP

#includereg52.h //包含头文件，一般情况不需要改动，头文件包含特殊功能寄存器的定义 #includeintrins.h #includemath.h #includestdio.h #includeabsacc.h #includectype.h #includestdlib.h sbit RS = P2^4; //定义端口 sbit RW = P2^5; sbit EN = P2^6; sbit P0_0 = P0^0; sbit P0_1 = P0^1; sbit P0_2 = P0^2; sbit P0_3 = P0^3; sbit P0_4 = P0^4; sbit P0_5 = P0^5; sbit P0_6 = P0^6; sbit P0_7 = P0^7; sbit P1_0 = P1^0; sbit P1_1 = P1^1; sbit P1_2 = P1^2; sbit P1_3 = P1^3; sbit P1_4 = P1^4; sbit P1_5 = P1^5; sbit P1_6 = P1^6; sbit P1_7 = P1^7; sbit P2_0 = P2^0; sbit P2_1 = P2^1; sbit P2_2 = P2^2; sbit P2_3 = P2^3; sbit P2_4 = P2^4; sbit P2_5 = P2^5; sbit P2_6 = P2^6; sbit P2_7 = P2^7; sbit P3_0 = P3^0; sbit P3_1 = P3^1; sbit P3_2 = P3^2; sbit P3_3 = P3^3; sbit P3_4 = P3^4; sbit P3_5 = P3^5; sbit P3_6 = P3^6; sbit P3_7 = P3^7; sbit B_0 = B^0; sbit B_1 = B^1; sbit B_2 = B^2; sbit B_3 = B^3; sbit B_4 = B^4; sbit B_5 = B^5; sbit B_6 = B^6; sbit B_7 = B^7; #define RS_CLR RS=0 #define RS_SET RS=1 #define RW_CLR RW=0 #define RW_SET RW=1 #define EN_CLR EN=0 #define EN_SET EN=1 #define DataPort P0 unsigned char code C[]={0,1,2,3,4,5,6,7,8,9}; /*------------------------------------------------ uS延时函数，含有输入参数 unsigned char t，无返回值 unsigned char 是定义无符号字符变量，其值的范围是 0~255 这里使用晶振12M，精确延时请使用汇编,大致延时 长度如下 T=tx2+5 uS ------------------------------------------------*/ void DelayUs2x(unsigned char t) { while(--t); } /*------------------------------------------------ mS延时函数，含有输入参数 unsigned char t，无返回值 unsigned char 是定义无符号字符变量，其值的范围是 0~255 这里使用晶振12M，精确延时请使用汇编 ------------------------------------------------*/ void DelayMs(unsigned char t) { while(t--) { //大致延时1mS DelayUs2x(245); DelayUs2x(245); } } /*------------------------------------------------ 判忙函数 ------------------------------------------------*/ bit LCD_Check_Busy(void) { DataPort= 0xFF; RS_CLR; RW_SET; EN_CLR; _nop_(); EN_SET; return (bit)(DataPort 0x80); } /*----------------------------------------