离合器课程设计绝对精品讲解.docxVIP

佳木斯大学课程设计说明书题目:北京牌轻型双排座载货汽车离合器的设计学生姓名：王世欣学号：专业年级：车辆13级指导教师：所属学院：机械工程学院二〇一六年七月六日摘要汽车离合器位于发动机和变速箱之间的飞轮壳内，用螺钉将离合器总成固定在飞轮的后平面上，离合器的输出轴就是变速箱的输入轴．在汽车行驶过程中．驾驶员可以根据需要踩下或松开离合器踏板，使发动机与变速箱暂时的分离和断开，使发动机向变速器输入动力：（1）是汽车平稳起步。（2）中断给传动系的动力，配合档位。（3）防止传动系过载。本设计主要针对某轿车设计的离合器。根据车辆使用条件和车辆参数，按着离合器系统的设计步骤和要求，主要进行以下工作；摩擦片外径的确定，离合器后备系数的确定，单位压力的确定。并进行总成设计主要为；分离装置的设计，及从动盘的设计（从动盘毂的设计），及圆柱螺旋弹簧的设计等。关键字：单片；干式；膜片弹簧；液压操纵；Abstractthe clutch is located in between the engine and transmission of the flywheel crust, screwed the clutch assembly fixed after the flywheel plane, clutch output shaft is gearbox input shaft. In automobile driving process. The driver stepped on the fly can according to need or loosen the clutch, make the engine and transmission temporarily separation and disconnected, make the engine to the transmission input power: (1) is car smooth start. (2) the interrupt to transmission power, cooperate a gear. (3) prevent transmission overload. This design is mainly aimed at a car designed clutch. According to the vehicle use condition and vehicle parameters, according to the clutch system design steps and requirement, mainly for the following work; Friction slices diameter determination, and clutch determination of unit is lengthened, pressure determination. And assembly design mainly for, Separation device design, and driven plate design (platen hub design), and the design of cylindrical helical spring etc.Monolithic???Dry?type; Film?spring; Hydraulic; control目 录摘要ⅠAbstractⅡ第1章 绪论11.1 概述11.2 离合器的基本组成和分类21.3 离合器的功用21.4 汽车离合器设计的基本要求2第2章 摩擦离合器基本结构尺寸、参数的选择42.1 摩擦片外径42.2 摩擦片内径42.3 摩擦片厚度52.4 校核离合器所选尺寸5第3章 离合器零件的结构选型及设计计算73.1 从动盘总成73.1.1 从动片73.1.2 从动盘毂73.2 压盖和离合器盖93.2.1 压盘设计93.2.2 离合器盖设计113.3 分离轴承及分离套筒11第4章 膜片弹簧的优化设计134.1 膜片弹簧设计?134.2? 膜片弹簧的结构特点?134.3 膜片弹簧基本参数的选择?134.4 ?膜片弹簧的优化设计144.5 弹簧材料及制造工艺?15第5章 扭转减震器的设计165.1 扭转减震器的概述165.2 扭转减震器的概述165.3 减震弹簧的计算17第6章 操纵机构设计206.1 选择操纵机构的结构型式206.1.1 机械式操纵机构?206.1.2 液压式操纵机构?206.1.3机械式和液压式操纵机构的助力器?206.2? 操纵机构的工作原理及尺寸参数的确定?216.2.