原创力文档- 1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
- 2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击 这里二次下载。
- 3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
- 4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
- 5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
- 6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
- 7、VIP文档为合作方或网友上传，每下载1次， 网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
实习 （实训）报告
名称 垫片复合冲压模具的设计
09年 1月 14 日至 09 年 2 月 25 日共 6 周
院 系 机电工程系
班 级 06模具1班
姓 名 刘金根
1
垫片复合冲压模具的设计
摘要：模具是现代工业的重要工艺设备，随着科学技术的不断进步，它在国民经济中占
有越来越重要的地位，发展前景十分广阔。装备制造业在2007年的迅速发展，尤其是汽车
和电子电器产品的高速增长，为模具工业的发展营造了良好的市场环境。本次综合实训设计
垫片的复合冲压模具，从零件的工艺性分析到模具结构的设计再到工艺计算，一直到最后的
模具装配图。
关键词：垫片、复合冲压模具、设计
2
目 录
引言 （绪论）···························································································1
一、冲裁件的工艺性分析············································································7
二、确定冲压工艺方案···············································································7
三、选择模具结构形式···············································································7
1.模具的形式··················································································4
2.定位装置·····················································································4
3.卸料装置·····················································································4
4.导向零件·····················································································4
5.模架···························································································4
四、必要的工艺计算··················································································8
1.排样设计与计算············································································4
2.计算冲压力··················································································4
3.计算模具压力中心·········································································4
4.计算模具刃口尺寸·········································································4
五、垫片复合
文档评论（0）