3318119房应坤毕业的设计中期检查汇报.pptVIP

卧式多轴双面钻机床总体设计 3318119 机制81 房应坤 指导老师：刘学军 机床的总体设计 机床的总体设计就是根据产品的零件图和装配图，生产纲领，现有资料等拟定 机床工艺方案和结构方案，并进行 方案图样和有关技术文件的设计。 工艺方案的制定 制定工艺方案是设计机床最重要的步骤。被加工零件需要完成的加工工序和应保证的加工精度是制定方案的主要依据。制定的三张加工工艺卡如下所示。 定位基准的选择 定位基准选定为“一面两孔”。 定位方案采用“一面两销”的定位方案。 以工件的底面为定位基准限制了三个自由度，短圆柱销限制了两个自由度，菱形销限制了一个自由度。 工序卡1 工序卡2 组合机床方案简图 专机化改造的方案简图 专机化改造的要点 （1）在原设备上增加专用主轴箱和刀具刀杆。 （2）为了提高工作台的精度和刚度，将工作台固定于托盘上，不作回转和横向移动 （3）拆除后立柱尾架，加大工作台的有效行程，以满足工件加工需要 （4）采取修复机床导轨。淬火等措施，提高机床耐用度。 （5）原钻床的主轴箱改造后可作为专用机床的动力箱使用 谢谢观看！ * * 制定工艺方案是设计组合机床最重要的步骤。被加工零件需要完成的加工工序和应保证的加工精度是制定方案的主要依据。 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client