EN 55024- 2010 for surge讲解.pptx

EN 55024- 2010 for surge讲解闫春平4.3 Surge limit / EN 55024Signal port, and telecommunication portsCopy fromTest specificationUnitsPerformance CriterionRemarkEN700 kV (Peak)Tr/Th μsC410/700 kV (Peak)Tr/Th μsSurge limit / EN 55024 Input ac power port(including equipment marketed with a separate ac/dc power converter)Copy fromTest specificationUnitsPerformance CriterionRemarkEN 550241(line to line)2(line to earth)1.2/50(8/20) kV (Peak)kV (Peak)Tr/Th μsBSurge limit / EN 55024 Input dc power port(excluding equipment marketed with a separate ac/dc power converter)Copy fromTest specificationUnitsPerformance CriterionRemarkEN 550240.51.2/50 (8/20)kV (Peak)Tr/Th μsBTest applied lines to earth4.3 Surge limit / ENG0002341Severity LevelLevelPulse position(degree)Line under testAcceptance Criteria1500kV0,90,180,270VdcB Note11500kV0,90,180,270Line to groundB Note11500kV0,90,180,270Neutral to groundB Note11500kV0,90,180,270Line to neutralB Note121kV0,90,180,270VdcB Note221kV0,90,180,270Line to groundB Note221kV0,90,180,270Neutral to groundB Note221kV0,90,180,270Line to neutralB Note232kV0,90,180,270Line to groundB Note132kV0,90,180,270Neutral to groundB Note1X(Dell req.)2.5kV0,90,180,270Line to groundB Note2X(Dell req.)2.5kV0,90,180,270Neutral to groundB Note2Note1:适用于R0和R1产品；Note 2:适用于R2产品波形校验/IEC61000-4-5 波形校验/IEC61000-4-5 波形校验/IEC61000-4-5 TEST SETUP/ IEC 61000-4-5TEST SETUP/ IEC 61000-4-5TEST SETUP/ IEC 61000-4-5TEST SETUP/ IEC 61000-4-58 试验程序8.1 实验室参考条件8.1.1 气候条件 除非通用标准，产品类标准和产品标准另有规定，实验室的气候条件应该在EUT和试验仪器各自的制造商规定的设备正常工作的范围内 相对湿度过高会引起EUT表面凝露则不能执行测试。8.1.2 电磁环境 实验室的电磁环境应被监控避免对EUT的正常操作产生影响。TEST SETUP/ IEC 61000-4-5TEST SETUP/ ENG0002341EUT放置在离接地平板10cm上的非导电木板，运行EMI测试程式。参考接地平板到EUT各边的投影要超过10cm。所有I/O都要运行读/写功能。键盘，鼠标等严格意义上只是属于输入设备,没有数据的传送。EUT的功能在整个测试中要被监控到。Workstation和server platforms当有多个供电系统时，可通过PDU同时连接到发生器。电源线长度为50cm.所有超过3m的I/O线缆通过CLAMP执行测试，如网线，信号线，并联线，USB线，串联线，1394线。Clamp放置距离EUT 50cm.(所有的被测线缆同时放在clamp中执行测试也是被允许的)测试时连接CDN用于对AE的信号隔离。在测试过程中要确保I/O线缆不能弯曲穿过容性耦合夹Surge Immunity EU