毕业设计（论文）-XK5032A螺母座工艺及钻4-M8螺纹孔夹具设计（全套图纸）.doc

四川理工学院毕业设计（论文） PAGE 32 PAGE 31 目录  TOC \o 1-3 \h \z \u  HYPERLINK \l _Toc475344836 第一章 零件的分析  PAGEREF _Toc475344836 \h 1  HYPERLINK \l _Toc475344837 1.1 零件图的分析  PAGEREF _Toc475344837 \h 1  HYPERLINK \l _Toc475344838 1.2主要技术条件分析  PAGEREF _Toc475344838 \h 1  HYPERLINK \l _Toc475344839 1.3 确定毛坯的制造形式  PAGEREF _Toc475344839 \h 1  HYPERLINK \l _Toc475344840 第二章 工艺规程设计  PAGEREF _Toc475344840 \h 2  HYPERLINK \l _Toc475344841 2.1 定位基准的选择  PAGEREF _Toc475344841 \h 2  HYPERLINK \l _Toc475344842 2.1.1 粗基准的选择  PAGEREF _Toc475344842 \h 2  HYPERLINK \l _Toc475344843 2.1.2 精基准的选择  PAGEREF _Toc475344843 \h 2  HYPERLINK \l _Toc475344844 2.2 确定个加工表面加工方案  PAGEREF _Toc475344844 \h 3  HYPERLINK \l _Toc475344845 2.2.1 在选择各表面及孔的加工方法时要综合的因素  PAGEREF _Toc475344845 \h 3  HYPERLINK \l _Toc475344846 2.2.2 零件表面加工方法的选择  PAGEREF _Toc475344846 \h 4  HYPERLINK \l _Toc475344847 2.3工艺路线的制定  PAGEREF _Toc475344847 \h 4  HYPERLINK \l _Toc475344848 2.3.1工序的合理组合  PAGEREF _Toc475344848 \h 4  HYPERLINK \l _Toc475344849 2.3.2 工序的集中与分散  PAGEREF _Toc475344849 \h 5  HYPERLINK \l _Toc475344850 2.3.3 加工阶段的划分  PAGEREF _Toc475344850 \h 5  HYPERLINK \l _Toc475344851 2.4制定工艺路线  PAGEREF _Toc475344851 \h 6  HYPERLINK \l _Toc475344852 2.5确定切削余量  PAGEREF _Toc475344852 \h 8  HYPERLINK \l _Toc475344853 2.5.1粗铣底面  PAGEREF _Toc475344853 \h 8  HYPERLINK \l _Toc475344854 2.5.2 粗铣螺母座的前面  PAGEREF _Toc475344854 \h 9  HYPERLINK \l _Toc475344855 2.5.3粗铣中间槽  PAGEREF _Toc475344855 \h 9  HYPERLINK \l _Toc475344856 2.5.4粗镗半精镗圆弧面  PAGEREF _Toc475344856 \h 9  HYPERLINK \l _Toc475344857 2.5.5三组孔加工  PAGEREF _Toc475344857 \h 10  HYPERLINK \l _Toc475344858 2.6确定切削用量及工时  PAGEREF _Toc475344858 \h 10  HYPERLINK \l _Toc475344859 2.6.1粗铣螺母座顶面  PAGEREF _Toc475344859 \h 10  HYPERLINK \l _Toc475344860 2.6.2粗精铣螺母座底面  PAGEREF _Toc475344860 \h 12  HYPERLINK \l _Toc475344861 2.6.3 粗精铣前后端面。