瑞士SOCOREX瓶口分液器耐腐性对照表.docx

A = Good resistanceB = Acceptable with limitationsC = Not recommendedA = 良好的耐受性B =可以耐受但是有限制C = 不推荐使用1 = Possible crystallisation – blockage (do not let dry plunger / barrel together).2 = Swell of plunger protection layer, possible peeling.3 = Acid vapours (better resistance with lower concentration).Do not leave instrument on bottle.4 = Risk of softening or discoloration of external parts through vapours.Do not leave instrument on bottle.5 = Chemical degradation of glass parts (plunger / barrel).1 可能形成结晶-阻塞（不要让活塞变干）。2 活塞保护层，可能脱皮。3 酸蒸气（建议用低浓度的试剂）。不要长久的将瓶口移液器放置在瓶口。4 由于溶剂挥发可能造成部件软化，或者部件推色。不要长久的将瓶口移液器放置在瓶口。5 化学降解的玻璃部件（活塞/活塞外壁）试剂名称501520521Acetic acid 100%醋酸100％AAB/1Acetic acid diluted稀释醋酸AAB/3Acetone丙酮AB/4AAcetonitrile乙腈AAAAscorbic acid抗坏血酸AAABenzaldehyde苯甲醛AAABenzene苯AB/4B/4Boric acid硼酸AAABromine溴B/2B/2C/2/4Butanol丁醇AAAButanone丁酮AB/4ACarbon disulfide二硫化碳AAAChlorobenzene氯苯AAAChlorobutane氯丁烷AAAChloroform氯仿AB/4B/4Chloronitric acid 100%硝酰氯; 王水B/2/3B/3C/3Chlorosulphuric acid 100%氯磺酸100％B/2/3B/3B/3Chromic acid 100%铬酸100％B/2/3B/3B/3Citric acid柠檬酸AAACyclohexane环己烷AAACyclohexanone环己酮AAADiethylene glycol二甘醇AAADiethylether二乙醚AAADimethylformamide (DMF)二甲基甲酰胺（DMF）AB/4ADimethylsulfoxide (DMSO)二甲基亚砜（DMSO）AAADioxane / Diethylene dioxide二恶烷1,4-二氧杂环己烷AAB/4Ethanol乙醇AAAEther醚AB/4B/4Ethyl acetate乙酸乙酯AAB/4Ethylene glycol乙二醇AAAFormaldehyde (Formalin)甲醛（福尔马林）AAAFormic acid蚁酸AAAGazoline汽油AAAGlycerin 40%甘油40％AAAHeptane庚烷AAAHexane正己烷AAAHydrochloric acid 37%盐酸37％B/2/3AB/3Hydrofluoric acid 100% (HF)100％的氢氟酸（HF）的C/5C/5C/5Hydrogen peroxide过氧化氢AAAIodine碘AAAIsopropanol异丙醇AAALactic acid乳酸AAALiquid ammonia液氨AAAMethanol甲醇AAAMethylchloride一氯甲烷AAAMethylen chloride (DCM)二氯甲烷;甲叉二氯AB/2/4B/2/4Methyl ethyl ketone MEK甲基乙基甲酮;甲乙酮;丁酮AB/4AMethylmethacrylate (MMA)甲基丙烯酸甲酯AAAMineral oil矿物油AAANitric acid 100%硝酸100％B/2/3B/3C/3Octane辛烷AAAOil, veg. / anim. / min.植物油，动物油等AAANitric acid dil. 30%稀硝酸30％AAAOxalic acid草酸AAAPerchloric acid 100%100％高氯酸B/2/3B/3B/3Perchloric acid diluted高氯酸稀释AAAPetrol benzene汽油苯AAB/4Petroleum ethe