万向节的毕业设计论文.docVIP

下载本文档

28
0
约2.39万字
约 12页
2017-05-19 发布于重庆
举报
版权申诉

万向节的毕业设计论文.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

万向节的毕业设计论文

目录目录· ······························ 1 · 目录································1 · 引言· ······························ 3 · 引言································3 · 零件的分析· ························ ·4 第一章零件的分析························· 4 · 1.1 零件的作用·························· 4 ·························· 1.2 零件的材料·························· 4 ·························· 1.3 零件的工艺分析························ 4 ························ 1.3.1. 结构分析···························· 4 ···························· 1.3.2 加工表面的技术要求分析····················· 5 ····················· ······················ 1.3.3. 表面处理内容及作用·······················5 第二章工艺规程设计····························· 5 · · · ·· · ·· · ·· ·· · · ·· · ·· · ·· ·· · · ·· 2.1 制定零件工艺规程的原则和技术要求··············· ···············6 3.1.1 工艺要求····························· ···························· 6 3.1.2 技术依据····························· ···························· 6 2.2 生产类型的确定························ ························6 2.3 确定毛坯的制造形式······················ ······················6 2.4 制定工艺路线及方法······················ ······················7 2.4.1 加工方法的选择························· ·························7 2.4.2 基准的选择··························· ···························8 2.4.3 制定工艺路线·························· ··························8 2.5 机械加工余量、工序尺寸及毛坯尺寸的确定············ 11 ············ 2.6 确定切削用量及基本工时···················· ··················· 14 2.6.1 加工条件····························14 ··························· 2.6.2 计算切削用量··························15 ························· ····························· 第三章夹具设计······························27 3.1 问题的提出·························· ························· 27 3.2 夹具设计··························· ·························· 27 3.2.1 定位基准的选择.························· ························ 27 -1- 3.2.2 切削力及夹紧力计算······················· ·······················27 3.2.3 定位误差分析·························· 28 ·························· 3.2.4 铣床夹具操作的简要说明·····················29 ···········