- 1、本文档共35页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
大学生-自行车变速系统的设计论文大学本科论文
毕业设计说明书
自行车变速系统的设计
班 级: 学号:
姓 名:
学 院: 软件学院
专 业: 软件工程
指导教师: 李彦栋 陈汝斌
2014 年 6 月
自行车变速系统的设计
摘 要
自行车变速系统的作用就是通过改变链条和不同的前、后大小的齿轮盘的配合来改变车速快慢。前齿盘的大小和后齿盘的大小决定了自行车旋动脚蹬时的力度。前齿盘越大,后齿盘越小时,脚蹬时越感到费力。前齿盘越小,后齿盘越大时,脚蹬时越感到轻松。根据不同车手的能力,即可通过调整前、后齿盘的大小调整自行车的车速,或是应对不同的路段、路况。
The design of bicycle transmission system
Abstract
The role of the bicycle transmission system is change the speed of thebicycle by changing the chain and the front and rear gear plate size . The size of the front and after chainring crankset determines the intensity of the bicycle pedal when rotating . The larger front chainring , The smaller behind chainring, more pedal feel effortless . The smaller front chainring , the bigger behind chainring , the more we feel relaxed when you pedal . Depending on the capabilities of different drivers , you can adjust the size of the chainring to respond to different sections of the road.
When want to chang the speed , the diver will act on the turn transmission .The shift transmission works is put the chain inwards or outwards .Since the gear tooth tip pulls the chain direction,when the chain is pushed into the contact area of the tooth tip. Due to the shift transmission and the tensioning action of the rear connecting shaft,achieve that the different speed requirements. Shift principle in front of the front sprocket wheel is the same basically, just a little bit different. As can be seen from the second, more two (the rear sprocket and the foot whee) radius of the wheel type, the more classes gear position.
Keywords:Bicycle, hift transmission, Transmission Device,derailleur
目 录
1 引言 1
2 自行车变速系统总体方案的论证 3
2.1 各级传动比以及主要参数的确定 3
2.1.1 概述 3
2.1.2 各级传动齿数的确定 3
2.1.3 链轮轴转速及功率的确定 3
2.2 确定变速系统各零件的设计顺序 3
2.3 运动计算的设计 3
3 自行车链条的设计 4
3.1 自行车链条的特点及主要的失效形式 4
3.1.1 自行车链条的特点 4
3.1.2 自行车链传动的主要失效形式有 4
3.2 链条的各参数的确定 5
3.3 确定零件材料及热处理工艺 5
4 后拨链器的设计 6
4.1 后拨链器的特点 6
4.2 后拨链器材料的选用 6
4.3
您可能关注的文档
最近下载
- 广州小升初真题白云区太和华附小升初入学数学卷.pdf
- 2024年北京急救中心“院前急救护士”岗位招聘考试2018-2023年真题荟萃含答案解析.docx
- 【北师大版】二年级数学上册全册33套试卷(附答案).pdf
- QB∕T 5612-2021 钛杯 QB∕T 5612-2021 钛杯 QB∕T 5612-2021 钛杯.pdf
- 海南省工程建设工法申报表.doc VIP
- 中国无线经济发展研究报告(2023年).pdf
- TDS-3410A型解吸管活化装置安装使用说明书.doc VIP
- 2022年秋季吉安市青原区幼儿园后勤人员招聘笔试试题及答案.docx VIP
- 2022最新整理自考英语写作基础试题及答案.docx
- 改名字授权委托书.docx
文档评论(0)