平行度检测医.pptVIP

平行度误差的检测 李瑞 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 平行度误差检测 概念 平行度公差是一种定向公差，是被测要素相对相对基准在方向上允许的变动全量。所以定向公差具有控制方向的功能，即控制被测要素对准基准要素的方向。 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 1.面对面的平行度公差 该项平行度公差为：所指表面必需位于距离为0.05mm，且平行于基准平面的两平行平面之间。 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 2.面对面的平行度公差 该图所示公差带是距离为公差值t且平行于基准平面的两平行平面之间的区域。 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 3.面对线的平行度公差 所指平面必须位于距离为0.05mm，且平行于基准轴线的两平行平面之间。 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 4.面对线的平行度公差 如图所示公差带是距离为公差值t且平行于基准轴线的两平行平面之间的区域 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 5.给定方向线对线的平行度公差 平行度公差为孔D的实际轴线必须位于距离为公差值0.2mm，平行位于基准轴线A且垂直于给定方向的两平行平面之间。 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 6.给定方向的线对线的平行度公差 如图所示公差带是距离为公差值t且平行于基准轴线且垂直于给定方向的两平行平面之间的区域。 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 7.任意方向上线对线的平行度公差 该项平行度公差为孔D的实际轴线必须位于直径为公差值0.1mm，轴线平行于基准轴线A的圆柱面所构成的公差带区域内。 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 8.任意方向上线对线的平行度公差 任意方向上线对线的平行度公差带是直径为公差值t，轴线平行于基准轴线的圆柱面内的区域。 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 平行度误差的检测方法——打表法 检验平板，带指示器的测量架 将被测零件放置在检验平板上，用平板 的工作面模拟被测零件的基准作为测量基准 测量实际表面上的各点，取指示器的最大读数 与