Nand Flash 寻址方式与其驱动程序.ppt

Multi-Plane Block Erase Multi-Plane Page Program Driver With C Controller Register Configure 2410 NFCONF 使能controller｜初始化ECC｜反片选｜TACLS｜TWRPH0｜TWRPH1 (115)|(112)|(111)|(TACLS8)|(TWRPH04)|(TWRPH10) 2440相对复杂一点，仔细看看，其实也差不多。 从Reset开始 NFCONF = ~0 // 片选 NFCMD = 0xFF; // 发命令0xFF //Read R/B wait idle while(!(NFSTAT0x01)) { for(i=0;i10;i++) { ; } } NFCONF |= 0 // 反片选 在使用FLASH之前一定要先Reset一下：Waiting for next command! Read ID NFCONF = ~0 // 片选 NFCMD = 0x90; // 发命令0x90 // Write Address 0x00 NFADDR = 0 0xFF; for(i=0; i10; i++); NFADDR = (0 9) 0xFF; for(i=0; i10; i++); NFADDR = (0 17) 0xFF; for(i=0; i10; i++); NFADDR = (0 25) 0xFF; for(i=0; i10; i++); //Read ID id = NFDATA24; // Maker code (K9F1208:0xEC) id |= NFDATA16; // Device code (K9F1208:0x76) id |= NFDATA8; // Must be don’t care (K9F1208:0x0xA5) id |= NFDATA; // Support multi plane operation (K9F1208:0xC0) NFCONF |= 0 // 反片选 Read 1 (One Page) NFCONF = ~0 // 片选 NFCMD = 0x00; // 发命令0x90 // write address 0xXXXXXXXX NFADDR = 0xXXXXXXXX 0xFF; for(i=0; i10; i++); NFADDR = (0xXXXXXXXX 9) 0xFF; for(i=0; i10; i++); NFADDR = (0xXXXXXXXX 17) 0xFF; for(i=0; i10; i++); NFADDR = (0xXXXXXXXX 25) 0xFF; for(i=0; i10; i++); //Read R/B wait idle while(!(NFSTAT0x01)) { for(i=0;i10;i++) { ; } } //Read One Page 512Byte Data for(j = 0; j 512; j++) { *buf = NFDATA0xFF; buf ++; } NFCONF |= 0 // 反片选 其它问题 SLC or MLC Nand Flash 寻址方式及其驱动程序 Nand Flash 寻址方式及其驱动程序 存储结构和寻址方式 命令和时序 2410、2440 Nand Controler Driver with C ECC 存储结构K9F1208U0M-YIB0 寻址方式K9F1208U0M-YIB0 Column Address [A0-A7][A8] 对应byte in page address 9bit寻址(512+16)byte/page Row Address [A9-A13]对应page in block address 5bit寻址32page/block [A14-A25]对应block in device address 12bit寻址4096block/device 存储结构K9F8G08X0M 寻址方式K9F8G08X0M Column Address [A0-A12] 对应byte in page address 13bit寻址(4K+128)byte/page Row Address [A13-A1