英文文献整理.doc

Substrate Cladding powder Laser parameters Reference AISI A2 100*100*10 mm AISI M2 AISI 431 Powder feeding 30 l/min Ar AISI M2 4g/min AISI 431 3g/min 400mm/min, 30% 2005Laser coatings to improve wear resistance of mould steel AISI 1020 0.14-0.22C, 0.4-0.65Mn, 0.12-0.3Si 100*15*10 mm Fe-40Ti 200mesh Graphite 180mesh molTi / molC =1:1 ball milling 1h mixed with sodium silicate 水玻璃 1-1.2mm HL-T5000D CO2 2.5kw, 5mm/s 4mm spot 10 l/min Ar 原位生成TiC增强Fe基 2009In situ synthesised TiC particles reinforced Fe based composite coating produced by laser cladding AISI 1045 100*40*10 mm 30%Fe-Ti, Fe-V, Graphite, 5%Fe-Mn, 3%Fe-Si, 5%CaF molV / molTi =0, 0.5, 1, 1.2 ball milled under Ar HL-T5000D CO2 2.5kw, 5mm/s 3mm spot 33%, powder feed 350mg/s 10 l/min Ar FeV%↑，TiC+(Ti,V)C → VC+(Ti,V)C 多相颗粒增强Fe基 2009Reaction synthesis of (Ti,V)C carbide reinforced Fe based surface composite coating by laser cladding 参考文献 AISI 1045 100*40*10 mm Fe-25-30Ti, Fe-45-50V, Graphite, 74 μm HL-T5000D CO2 2.5kw, 5mm/s 3mm spot 33% 10 l/min Ar TiC+(Ti,V)C增强Fe基 2010Microstructure and wear properties of in situ multiple carbides reinforced Fe based surface composite coating produced by laser cladding AISI 1045 100*40*10 mm Fe-25-30Ti, Fe-65-75Mo, Graphite, 0-5-10-15%Fe-Mo 74 μm 1.2 mm HL-T5000D CO2 2.5kw, 5mm/s 3mm spot 33% 10 l/min Ar TiC+(Ti,V)C增强Fe基 AISI 1020 50*20*10 mm 砂纸研磨-丙酮清洗-预置粉末 Fe38Ni30Si16B14V2(at.%) 纯单相粉末混合100-200目+水玻璃 1 mm HL-T5000 CO2 三步： (1) 2kw, 5mm/s 3mm spot (2) 2.5kw, 10 mm/s (3) 4.8kw, 5mm/s 2mm spot 15 l/min Ar (Ti,Mo)C增强Fe基 2009Microstructure and wear properties of laser clad Fe based amorphous composite coatings Mild steel 20*20*10 mm 316L(45~60 μm) + 5% / 20% SiC(25-40 μm) 700,800,900,1000w 3.5~7.5 mm/s 60 mg/s 6 l/min Ar 316L-5%SiC 250-340 VHN SiC+Cr2C3 316L-20%SiC 450-800 VHN SiC+Cr2C3+Fe2Si 316L stainless steel 155VHN 700w, 7.5 mm/s 2009Studies on Direct laser cladding of SiC dispersed AISI 316L Stainless Steel 316 stainless steel 316L(-45~+15 μm) + 20-33-50vol.