Flexi_MCPA_硬件介绍_诺基亚.ppt

下图为配置2个RF模块1个小区时的接法，2个RF模块最大可做到12+12+12的配置 天馈系统的连接，下图为配置1个RF模块3个小区时的接法，可做到最大6+6+6的配置 Network on the background, boxes appear by animations EAC connector pin assignments The EAC connector on the RF module is an RJ45 connector with 4 input lines. It is typ- ically used for monitoring local alarms when the RF Module is located far away from the System Module. The EAC connector can also be used for monitoring FPMA or FPDA alarms when these modules are used for supplying power to the remote RFModule. The EAC alarm lines are configured with the 2G Flexi BTS Site Manager during commission- ing. They cannot be configured with the BSC. The cable connected to the EAC connec- tor is not auto-detected. Alarms are monitored by the RF Module and reported to the System Module via the optical cable. Alarm lines must be grounded to test the alarms (if configured as “Closed when active”). AlarmDescription PinNumber Technology Direction LineId1 5 TTL Input LineId2 6 TTL Input LineId3 1 TTL Input LineId4 4 TTL Input Ground 7 - - Table 9 EAC connector pin assignments Flexi BTS_MCPA 多载波功放基站 Flexi BTS_MCPA 基站详解 Flexi BTS_MCPA 基站应用 Flexi BTS_MCPA 多载波功放基站简介 Flexi BTS_MCPA 基站在现网使用的思考 分布式基站 市区覆盖 分布式基站 公路铁路覆盖 分布式基站 乡村覆盖 Flexi BTS_MCPA基站：全天候全场景应用 室内覆盖 (微蜂窝) 室外宏基站 室内宏基站 12载频 RRU 18载频3 扇区 射频模块 Flexi BTS_MCPA 宏基站 12载频 RRU 系统模块 Flexi BTS_MCPA 基站应用----乡村覆盖 (塔顶) 应用特点： 仅需一个RRU即可实现3扇区6/6/6覆盖 RRU置于塔顶，免馈线安装，避免馈线损耗，增大覆盖范围 BBU置于塔底，方便安装配电和传输设备 BBU通过光纤和直流电缆连接RRU BBU+RRU全室外安装，无需室外机柜 射频模块(RRU) 3扇区 光纤+直流供电 系统模块 ( BBU) * Up to 40KM with Single mode fiber Flexi BTS_MCPA 基站应用----市区覆盖 * Up to 40KM with Single mode fiber Sector 1 扇区1 扇区2 扇区3 楼顶室外站示例 应用特点： 仅需一个RRU即可实现3扇区6/6/6覆盖，满足市区高话务量需求 RRU置于天线下，减小馈线损耗 BBU通过光纤和直流电缆连接RRU BBU+RRU全室外安装，无需机房，无需室外机柜，解决市区站址难题 射频模块(RRU) +系统模块(BBU) Flexi BTS_MCPA 基站应用----公路铁路覆盖 2扇区RRU 2扇区RRU 2扇区RRU 系统模块(BBU) 应用特点： 仅需一个RRU即可实现2扇区6/6覆盖，道路覆盖最佳选择 RRU置于塔顶，免馈线安装，避免馈线损耗，增大覆盖范围 BBU通过光纤连接RRU，支持RRU串联 BBU+RRU全室外安装，无需机房，无需室外机柜，投资更省 配合NSN的基站接收机优化功能软件，目前已